PHILIPS AZ2055/05
Owner's Manual

English
TOP AND FRONT PANELS (See 1) 1SOURCE � selects CD/ TUNER / TAPE function 2y � power on/ off switch 3Display � shows the status of the set 4Cassette recorder keys RECORD 0 � starts recording PLAY 2 � starts playback SEARCH 5/6 � fast winds/rewinds tape STOP/OPEN 9/ � opens the cassette compartment � stops the tape PAUSE ; � pauses playback or recording 5BASS, MID, HIGH � EQ keys to adjust the bass, mid & treble frequencies 6PROG CD: programmes tracks and reviews the programme; Tuner: programmes preset radio stations Navigation controls 7�, § CD: � searches back and forward within a track; � skips to the beginning of a current track/ previous/ later track Tuner: � tunes to radio stations (down, up). 82; � starts or pauses CD playback 99 � stops CD playback; � erases a CD programme 0MODE � selects different play modes: e.g. REPEAT or SHUFFLE (random) order !PUSH TO OPEN � opens/closes the CD door @VOLUME � to adjust volume level #REMOTE SENSOR (for AZ2055 model only) � infrared sensor for remote control $PRESET DOWN/ UP (�, +) � selects a preset tuner station (down, up) %BAND � selects waveband ^DBB � (Dynamic Bass Boost) activates a more vivid bass response BACK PANEL

CONTROLS
&Telescopic aerial � improves FM reception *Battery compartment � for 6 batteries, type R-20, UM1 or D-cells (p � 3.5 mm stereo headphone socket Note: The speakers will be muted when headphones are connected to the set. )AC MAINS � inlet for mains lead REMOTE CONTROL (for AZ2055 only) 1VOLUME 3,4 � adjusts volume level (up, down) 2SHUFFLE � plays all CD tracks in random order 32; � starts/ pauses CD playback 4SEARCH 5, 6 � searches backwards/ forwards within a track 5PRESET +, � � selects a preset radio station (up, down) 6TUNING �, § � tunes to tuner stations (down, up) 79 � stops CD playback; � erases a CD programme 8¡, � � skips to the beginning of a current track previous/ subsequent track 9REPEAT � repeats a track /programme/ entire CD CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation. IMPORTANT! For users in the U.K.: please follow the instructions on the upper righthand-side.

BASIC FUNCTIONS
MAINS SUPPLY Whenever convenient, use the mains supply to conserve battery life. Make sure you remove the power plug from the set and wall socket before inserting batteries. Batteries (not included) � Insert 6 batteries, type R-20, UM-1 or D-cells, (preferably alkaline) with the correct polarity. Remote control (for AZ2055 only /See A) � Insert 2 batteries, type AAA, R03 or UM4 (preferably alkaline). Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. � Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. � When inserting new batteries, do not try to mix old batteries with the new ones. � Batteries contain chemical substances, so they should be disposed of properly. Using AC Mains 1 Check if the mains supply, as shown on the type plate located on the bottom of the set, corresponds to your local mains supply. If it does not, consult your dealer or service centre. 2 If your set is equipped with a voltage selector, adjust the selector so that it matches with the local mains. 3 Connect the mains lead to the wall socket. 4 To disconnect the mains supply, unplug the set from the wall socket. Auto-Standby mode When a CD or tape has reached the end of playback and remains in the stop position for more than 15 minutes, the set will switch off automatically to save mains. The type plate is located on the bottom of the set. BASIC FUNCTIONS Switching on and off and selecting function 1 Press y on the set to switch on. 2 Press SOURCE once or more to select: CD, TUNER or TAPE function. 3 Press y to switch off the set. Notes: � To change from TAPE to TUNER or CD function, or when you are switching off the set: first, make sure you press the tape STOP 9 key to end playback and all the cassette keys are released. � The tone, sound settings, tuner presets and the volume level (up to a maximum volume level of 20) will be retained in the set�s memory. Adjusting volume and sound 1 Adjust the volume with the VOLUME control. � Display shows the volume level and a number from 0-32. (See 2) 2 Press DBB once or more to select dynamic bass boost on or off. � Display: shows when activated. 3 To adjust the bass, mid and treble tones, press and hold + or � on the BASS, MID, HIGH keys until you reach the desired level, �5 to +5 � Display briefly shows BASS, MID, or HIGH and the level. (See 3) Note: To prevent sound interference the bass control options operate exclusively. You cannot combine the bass from BASS with DBB � The display shows or the indicator is automatically switched off to remind you if you attempt to use both bass settings.