|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I ordered this manual sometime in the afternoon and I received it on my e-mail the same evening.
This is a fantastically good and properly scanned copy of the original manual. All pages are of the same scale and they overlap each other. It means that you can print the manual and easily make it as a convenient paper manual.
The content of the manual is fantastic. Alignment descriptions, PCB layouts and elementary diagrams are explicit and precise. I immediately found what I was looking for. Thanks to this manual and Owner-Manuals.com my amplifier is alive again. Many thanx indded!
;
The manual was well-scanned and easy to read. As an added bonus, the Operator's Manual was bundled with the Service Manual!
I'd definitely use owner-manuals.com again.
;
Finally, i found one website, where i can download this service manual , and fix my hifi. The service manual is very good, and easy to download and to print.
 ;
Complete and very useful. Could have benefited from a little higher resolution on the schematic and layout diagrams for improved legibility.
;
Great Service Manual, Very Complete, as advertised, Perfect, Thanks!
D
Ausstattung des Arbeitsplatzes:
(Betriebspannung service 14,4 V)
GB
Work place equipment:
1. Netzgerät 15 V regelbar, 10 A
1. Power supply unit 15 volts adjustable, 10 A (Supply voltage service 14,4 V) 2. Signal generator (Meguro, Leader, Kenwood) 3. High impedance voltmeter Ri > 10 M� 4. Output meter; frequency counter; AF millivoltmeter; stereo encoder
2. Me�sender (z.B. Meguro, Leader, Kenwood) 3. Hochohmiges Voltmeter Ri > 10 M� 4. Outputmeter; Frequenzzähler; NF-Millivoltmeter; Stereocoder 5. Oszilloskop: - Empfindlichkeit: 5 mV bis 50 Volt/cm. - Bandbreite: Gleichspannung bis 50 MHz. 6. Tastköpfe 10:1 und 1:1 7. Schraubendreher / Abgleichstifte (keramisch) 8. Lötstation
5. Oscilloscope: - inp. sensitivity: 5 mV to 50 volts per division - bandwidth: d.c. to 50 MHz 6. Probes 10:1 and 1:1 7. Screwdriver / adjusting pins (ceramic) 8. Soldering station
Reparaturhinweise
Programmieren der Geräteparameter:
(ist nach Auswechseln von D860 / HF - Teil erforderlich) - FM ZF-Ablage - Suchlaufstoppschwellen FM - Programmierung der Stereo Schaltschwelle - RDS Schaltschwelle - Suchlaufstoppschwellen MW - Suchlaufstoppschwellen LW
Repair notes
Parameter programming:
(required after replacement of D860 / RF tuner) - FM IF offset - Seek tuning stop thresholds FM - Stereo threshold - RDS threshold - Seek tuning stop thresholds MW - Seek tuning stop thresholds LW
Servicemode
Servicemode aktivieren 1. Schalten Sie das Autoradio aus. 2. Betätigen Sie die Tasten 1 + 3 gleichzeitig und halten Sie die Tasten gedrückt. 3. Schalten Sie das Gerät ein und halten Sie die Tasten noch für ca. 1 Sekunde gedrückt.
Service mode
Activating the service mode 1. Switch the unit off. 2. Press the push-buttons 1 + 3 simultaneously and hold them depressed. 3. Switch the unit back on and hold on to the buttons for approximately one more second.
Nach diesem Schritt erscheint im Display für 2 Sekunden "SERVICE" und der manuelle Sender - Suchlauf ist unwirksam.
After this step the display will indicate "SERVICE" for 2 seconds and the manual tuning is inhibited.
Sie verlassen den Servicemode durch Ausschalten des Autoradios.
You can quit the service mode by switching the radio off.
-7-
|
|
|
> |
|
