|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Delivery came quite promptly and in a very readable format. Thank you.
;
I found my Clarion VRX8370R in the Camper I bought and I wasn't able for month to understand it.
The Owner Manual was perfect and just what I was searching for.
Thank you.
Leonardo
;
Very good copy of Manual, clear and easy to print off, arrived very promptly and reasonably priced.
Thanks, I will use you again.
;
Zeer duidelijke afdrukken op A4-formaat , zeer uitgebreide handleiding . Pluspunt ,zeer snelle
respons van jullie , binnen de 24h . Top !!!
;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
B100 TWO CHANNEL POWER AMPLIFIER BALANCE either absent or unacceptable. When the left/right signal balance is being shifted one of these LEDs will light to indicate which channel is being attenuated. Balance can be adjusted in 1dB increments to up to -6dB in either direction. Stepping past -6dB in either direction will mute that channel fully and the LED for that channel will turn red.
REMOTE POWER CONTROL ~ 12 VOLT TRIGGER CONNECTOR:
Two trigger outputs are provided. A 12Vdc signal is placed across the T1 and C pins of the 12V TRIGGERS connector whenever the unit is fully powered up. Then the unit goes into standby this voltage is removed. A 12Vdc signal will be placed across the other pair of 12V TRIGGER output pins (T2) whenever a certain user programmed input is selected as the source input (see below for programming instructions). When any other input source is selected the 12Vdc control voltage will be removed from these pins. Please note that C means �common� here and both C pins are electrically connected and identical.
PROGRAMMING the �T2� 12v TRIGGER OUTPUT:
By default the T2 triggered output is inactive. To program this output to become active , whereupon a control voltage of 12Vdc will appear across T2 & C terminals whenever a specific source is selected, use the handheld remote control as follows: � select the source that you want to coincide with T2 going active. � While pointing the remote control at the B100, press the CODE button, followed by the three digit code �247� using the keys numbered 1 through 0 in the illustration at the left. On your remote control these keys, or buttons, are labeled AUX/PH (2), ANALOG TUNER (4), DIGITAL CD (7). � The three digit code should be entered within a few seconds of pressing CODE button or the unit will automatically return to normal operation. � To clear the T2 trigger output, press the CODE button followed by the 3 digit code �248�: AUX/PH (2), ANALOG TUNER (4), DIGITAL TUNER (8).
HAND-HELD INFRA-RED REMOTE CONTROL:
The Bryston model B100 comes standard with a full function hand-held remote control unit. The hand held remote unit is powered by two �AAA� batteries. To change the battery remove the bottom cover plate by removing the four Philips screws on the rear of the remote unit. Ensure that the batteries are correctly oriented and properly seated in the battery holder. The B100 remote is a full function remote. It allows selection of all sources, volume up or down (the volume control is a motor-driven design), mute ,left/right balance, power on/off and discrete code entry. We recommend maintaining a direct line-of-sight between the hand held remote unit and the front of the B100 to ensure the most efficient operation of the remote features. 3
|
|
|
> |
|
