|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
;
Excellent product and service. I bought a second-hand Casio CPS-60 keyboard which had no manual. Packed full of features which I had no idea how to operate . . .
Google search found this site (and others with the same manual for sale for $8.99!)
I bought the manual and within an hour the download was available. Quality of the scanned images is good - very clear - and the PDF has been created with the pages in the correct order.
I would definitely use this site again.
B2/B2R Bass Amplifier
The Front Panel Controls and Their Use
40Hz
80Hz
150Hz
300Hz
600Hz
900Hz
2kHz
5kHz
8kHz
INPUT
PAD
GAIN
BASS
ULTRA MID
TREBLE
MASTER
LIMITER
+12dB
POWER
0
-12dB
-15dB PEAK LIMIT EQ ON ON
1
2
3
4
5
6
7
8
9
10
11
12
13
1. 0dB (INPUT): The signal output from an instrument (active or passive) or a line level signal may be connected here by means of a shielded instrument cable. 2. 15dB PAD: This switch, when depressed, attenuates the input signal by 15dB. Attenuation allows the Gain control (#4) to be used over a larger portion of its range. If clipping is indicated with the Gain control near minimum, attenuation is needed. 3. PEAK LED: This LED flashes when the signal level into the preamp approaches clipping. Adjust the Gain control (#4) until a strong signal from your instrument causes this LED to flicker. NOTE: If the LED flashes frequently with the gain at a low setting, use the 15dB Pad (#2) to attenuate the input signal and readjust the Gain. 4. GAIN: This serves as the input level control for the amplifier. For the best signalto-noise ratio set this control so the Peak LED (#3) flashes when you strike a string fairly hard. 5. BASS: This is the primary low frequency control which allows for 8dB of cut or boost at 50Hz.
6. ULTRA-MID: This is the primary midrange control. Rotate the control to the left of center for a �contoured� sound (more distant, less midrange output) or to the right of center for a pronounced (more upfront) tone. 7. TREBLE: This is the primary high frequency control which allows for 12dB of boost or 19dB of cut at 5kHz. 8. MASTER: Set the overall output level of the amplifier with this control. The Effects Loop and Balanced Out (#19-21,24) are not affected by the Master control. 9. LIMITER: The B2/B2R uses an internal Optocoupler Limiter to assist in keeping the power amplifier�s output �clean� at extreme volume levels. (All amplifiers begin to clip their output signals as they approach maximum output levels, resulting in distortion which may damage your speakers.) To engage the Limiter, depress the Limit switch. Whenever the amplifier is at full power, the adjacent LED will flash. This is an indication that the limiter is keeping peak signals from clipping the output. NOTE: Playing at full power with the Limiter off will give you increased output power, but the sound may be distorted. Use discretion when playing without the Limiter.
10. EQ ON SWITCH: Depress this switch to activate the Graphic EQ. The adjacent LED illuminates when the EQ is on. 11. GRAPHIC EQ: These sliders control the output of the frequencies indicated above each control. The center position of each control is flat (no boost or cut). 12. POWER ON LED: This LED indicator illuminates when the POWER switch (#13) is ON. 13. POWER SWITCH: This heavy-duty rocker switch applies the power to the amplifier. The amp is ON when the top of the switch is depressed, OFF when the bottom of the switch is depressed.
4
|
|
|
> |
|
