|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
5
6
7
8
Simple Error Rate Measurement
To measure the error rate for a certain duration, press the ESC then SIDE-B keys only during playback. The result of judgment (OK/NG) will be displayed on the FL display and as an OSD. To exit Error Rate Measurement mode, press the ESC key while the error rate is being measured. After exiting Error Rate Measurement mode, if the ESC then SIDE-B keys are pressed again to reenter Error Rate Measurement mode, measurement of the error rate will start from the beginning. The error rate is measured for up to 5 sessions, and the displayed result is updated after measurement for each session is performed. At the end of 5 sessions, the average error rate for the entire measurement range will be displayed. If measurement sessions are interrupted before 5 sessions, the average error rate up to the point of interruption will be calculated and displayed. A result will be judged as NG if the measured error rate exceeded the reference value. See "OK/NG judgment" below. (Only when the average error rate is judged as NG, the tray will be opened.)
A
B
Display Formats on the FL display and as an OSD Operation
Only during playback, if keys are pressed, calculation of error rate is started, and the results are displayed on the FL display and as an OSD. The symbol (-) (which indicates that measurement is not finished) flashes. The result of measurement is displayed. If error rate measurement is completed before playback finishes, the average error rate, the symbol (*) (which indicates that the measurement is completed) and the judgment result (OK/NG) will be displayed on the FL and as an OSD. (When NG is displayed, if the tray is opened, the indications on the FL display and screen will be retained.) If error rate measurement is not completed before playback finishes, the average error rate, the symbol (-) (which indicates that measurement is not finished) and the judgment result (ERROR) that indicates that the error rate measurement has not been completed will be displayed on the FL display and as an OSD.
Display format FL
ER x . x E - x ER x . x E - x (At lights out) (At lighting)
OSD
ERR RATE : x.xE-x (At lights out) ERR RATE : x.xE-x- (At lighting)
C
ER x . x E - x �
ERR RATE : x.xE-� OK (NG: OSD whole screen display with red)
ER x . x E - x -
ERR RATE : x.xE-x- ERROR
* The layout for OSD depends on the mounting. * "x.xE-X" in the above table indicates an error rate. E.g.: 3.5E-5 = 3.5X10-5
D
OK/NG judgment Disc type
DVD BD CD
Reference value
1.0x10-3 1.0x10-3
No error rate measurement
Indication
OK/NG OK/NG
E
F
BDP-LX71
5 6 7 8
33
|
|
|
> |
|
