|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is the original manufacturers service manual, with detailed info on the circit boards, explosion drawings of all parts in assembly order, and tuning instructions. The only thing missing is the information on the dimensions of the various drive belts. mail me if you need them. gcrossman_at_aol.com
;
Ordered service manuel for a hard to find plasma tv - your company made it easy to find and purchase - I will use you again
Thanks for your help
 ;
This is a high quality manual with clear schematic and components layout diagrams ; with service procedure included.
;
This service manual for the Kenwood KT-990D was reproduced really well ,is very legible and manual is complete.Combined with the low price paid,in the future,I will be checking Owner-Manuals.com any time I need a manual.
;
When I purchased this manual I had my doubts regarding the quality as the price was so reasonable as compared to other outlets.
The manual itself is of high standard the print is very clear as are the diagrams. Obviously with the diagrams one has to zoom in otherwise it is to small to be able to read.
Overall I am very pleased with the company who delivered as they said and with the manual they supplied.
I occasionally require a manual and now having registered with this company I shall order from them in the future.
2-5. Boards Replacement
2-5-4. PSW-61 Board
n When the PSW-61 board is replaced, replace a whole harness (H61) that is connected to PSW-61 board. 1. Disconnect the power cords from the rear panel. 2. Remove the cover. (Refer to Section 2-2-2.) 3. Remove the front panel (lower) and ornamental panel A. (Refer to Section 2-2-1.) 4. Open the front panel A. (Refer to Section 2-4-2.) 5. Remove the power supply units. (Refer to Section 2-42.) When there is one power supply, remove the blank panel. (Refer to Section 2-5-2.) 6. Remove the all HDD units. (Refer to Section 2-4-3.) 7. Remove the front stay. (Refer to Section 2-5-2.) 8. Remove the two power guides. (Refer to Section 2-52.) 9. Remove the IF positioning bracket. (Refer to Section 10. 11. 12. 2-5-2.) Unstick the filter from the front panel A. (Refer to Section 2-4-5.) Remove the LCD case lid. (Refer to Section 2-5-3.) Disconnect the two connectors (CN1, CN4) of the harness connected to the DP-269 board. (Refer to Section 2-5-3.) Remove the DP-269 board. (Refer to Section 2-5-3.) Remove the cable clamp. (Refer to Section 2-5-3.) Remove the PSW-61 board from the front panel A. (Refer to Section 2-5-3.) Cut the two harness clampers.
17. Disconnect the two connectors (CN1, CN10) of the harness connected to the AC-188 board . 18. Remove the all optional boards. (Refer to Section 2-55.) 19. Remove the four screws (BVTT 3x6) and two screws (PSW 3x6). 20. Pull out the noise filters until the harness is viewed. n Be sure not to pull out the harness connected to the noise filter. 21. Remove the four connectors of the harness connected to the noise filters. 22. Remove the PSW-61 board connected to the harness (H61).
BVTT 3x6
Noise filters
CN1 PSW 3x6
CN10
13. 14. 15. 16.
AC-188 board PSW-61 board
23. For installation, perform the removal procedures in reverse order. n Use the commercially available harness clamper .
PSW-61 board Harness clampers
MAV-70
2-21 (E)
|
|
|
> |
|
