|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
Section 1 Installation
1-1. Outline
The BKP-590 is a circuit board kit that enables Betacam CCD color video cameras such as the BVP-90 and others (excluding BVP-5/50) to be connected directly to the CCU-700 series via the CA-57A/57AP. Wide band transmission The video bandwidth is extend to 10 MHz by increasing the transmission bandwidth of the triax system. NCS (New Command System) is supported Owing the BKP-590, a conventional camera can be connected to the new command system (used in the CCU700 series) which is employed in the Sony camera. 1. Loosen the four screws and remove the side panels (left and right).
Screws
Side panel (left)
CA-57A/57AP
Side panel (right)
Screws
1-2. Installation
n Before installing the BKP-590 to the CA-57A/57AP, remove the triax cable from CCU connector so that the BKP-590 is installed to the CA-57A/57AP with the triax cable removed. Contents of BKP-590 MD-111 board TR-92 board IF-562 board MPX filter Cushion Hexagon support Discernment label CCU label Lithium battery *1) 2. Remove the MD-74, TR-60 and IF-424 boards. 3. Remove the one screw and remove the shielding plate.
:1 :1 :1 :1 :2 :2 :1 :1 :1
Screw
*1): As necessary, remove the two solder on the IF-562 board, replace the lithium battery (BT1).
Lithium battery
+ lead
IF-562 board
IF-424 board Shielding plate TR-60 board MD-74 board
� lead
BKP-590
1-1(E)
|
|
|
> |
|
