|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It's exactly a complete and very useful manual with all details what I needed. Thank you!I will come back whenever I need your manuals or schematics.
;
I searched EVERYWHERE looking for the manual/s on this "extinct" amp. Owner-Manuals.com made it available and for nearly nothing. Thanx to them, I can decipher the unknown cables and sort them out. Thanx, Owner-Manuals.com!!
;
Yes thank you i got the file i was after. There was a slight problem in my communication but it all worked out well.
A job well done.
 ;
Great manual...really saved me. The only problem is that I thought I would be able to download it directly when I paid for it but never received the download instructions until the next morning. The board trace pages were somewhat light also: really need to turn up the contrast on the printer before printing them. The schematic page was great; very clear! Well worth the money.
;
I've been in the electronic business for a long time. I used to buy Sam's Photofact for my needs which intailed having to go to the store and paying about $20 for a package of 3 different units so I was forced to buy more than I needed just to get one.
Owner manual is just at your keyboard and the information is almost instantansouly and the cost is very reasonable. Easy to print out if needed or simply read off of the screen. The larger the screen the better for obvious reasons.
2-1. Electrical Alignment Overview 2-2. Preparation for Adjustment 2-3. Free-running Frequency Adjustment
2-1-3. Initial Setting of Switches/Variable Resistors
ADC-35 Board
RV401 RV404 TP411 RV402 RV407 S601 RV408 TP412 COR402 COR401 S602 S504 E5 S401 RV406 TP403 RV405 S500 TP402 RV400 RV102 RV203 RV303 RV403 RV501
2-2. Preparation for Adjustment
1. Connect the equipment and tools. (Refer to Section 21-2.) 2. Set the switches on the ADC-35 board. (Refer to Section 2-1-3.) 3. Turn on the power of the digital interface unit (PFVD20/D50/D100A/D200A/D300) and warm up the unit for about 10 minutes.
2-3. Free-running Frequency Adjustment
Measurement equipment Oscilloscope Frequency counter Procedure 1. Supply 100% color bars signal from the signal generator to the ANALOG IN connectors. 2. Set the oscilloscope as follows. CH2 : 0.5 V/DIV AC TIME : 20 ns/DIV TRIG : CH2 (TP403) 3. Connect the CH2 probe of the oscilloscope to TP403. Connect the GND probe to E5. 4. Turn 1RV406 clockwise until the frequency level satisfies the specification. 5. After the adjustment is completed, set S401 to OFF. Measuring point : TP403 (J-6)/ADC-35 Adjustment point : 1RV406 (H-6)/ADC-35 Specification : 26.9 ±0.1 MHz
Component side (A side)
n 1RV203 (F-2) and 1RV303 (F-3) are used for factory setting. Do not change the settings. Set the switches before the adjustment as below.
Ref. No. (Address) S401 (G-6) S500 (H-5) S504 (A-6) S601 (A-4) S602 (A-5) 1RV406 (H-6) 1RV501 (H-4) Initial Setting ON H INT CCIR YUV Counterclockwise Mechanical center
2-2 (E)
BKPF-101CB
|
|
|
> |
|
