The service manual when downloaded and printed out was clear and easy to read. The manual is complete with the schematic diagram and technical data. I occasionally require a manual and now having registered with this company I shall order from them in the future.
Hello from Germany - thank you very much for the manual for my Sharp "Searcher" - the handling of your internet area is outstanding..Mike
Text excerpt from page 107 (click to view)
Mastering Tool Kit Parameter Functions
Compressor
This compresses the overall output signal when the input volume level exceeds a set value.
Mixer
Adjusts the volume of each frequency band.
Lo Level
-80� +6 dB
On/Off
This parameter turns the compressor effect on/off.
OFF, ON -24�0 dB
Sets the volume level of the lower range after the signal passes through the expander and compressor.
Lo Thres
Mid Level
-80� +6 dB
This sets the volume level at which the lower-range compressor goes into effect.
Sets the volume level of the midrange after the signal passes through the expander and compressor.
Lo Ratio
1:1.00�1:16.0, 1:INF
Hi Level
-80� +6 dB
This sets the ratio of suppression of the lower-range output when the input level exceeds the Lo threshold level.
Sets the volume level of the upper range after the signal passes through the expander and compressor.
Lo Attack
0�100 ms
This sets the time it takes for the lower-range compressor to go into effect once the input level exceeds the Lo threshold level.
Limiter
This suppresses high-level signals to prevent distortion.
Lo Release
This sets the time it takes for the lower-range compressor effect to stop once the input level falls below the Lo threshold level.
50�5000 ms
On/Off
Sets the limiter to ON or OFF.
OFF, ON -24�0 dB 0�100 ms
Mid Thres
-24�0 dB
Thres Attack
This sets the volume level at which the midrange compressor goes into effect.
Adjust this as appropriate for the input signal from your bass. This sets the time it takes for the limiter to go into effect once the input level exceeds the threshold level.
Mid Ratio
1:1.00�1:16.0, 1:INF
This sets the ratio of suppression of the midrange output when the input level exceeds the Middle threshold level.
Release
50�5000 ms
Mid Attack
0�100 ms
This sets the time it takes for the midrange compressor to go into effect once the input level exceeds the Middle threshold level.
Adjusts the time until when the limiter will turn off after the input level falls below the threshold level.
Mid Release
50�5000 ms
Output
This makes settings that affect the overall output.
This sets the time it takes for the midrange compressor effect to stop once the input level falls below the Middle threshold level.
Hi Thres
into effect.
-24�0 dB
Level
-80� +6 dB
This sets the volume level at which the upper-range compressor goes
Sets the volume level of the overall sound after the signal passes through the limiter.
Hi Ratio
1:1.00�1:16.0, 1:INF
Soft Clip
Off, On
This sets the ratio of suppression of the upper-range output when the input level exceeds the Hi threshold level.
This suppresses noticeable distortion occurring with heavy use of the compressor/limiter effect.
Section 3
Hi Attack
0�100 ms
Dither
OFF, 24�8 BIT
This sets the time it takes for the upper-range compressor to go into effect once the input level exceeds the Hi threshold level.
This prevents the action of muting sounds from being too noticeable.
Hi Release
50�5000 ms
This sets the time it takes for the upper-range compressor effect to stop once the input level falls below the Hi threshold level. * With the compressor, the level is automatically adjusted to the optimum setting according to the threshold (Thres) and ratio (Ratio) settings. In addition, since lengthening the attack (Attack) setting may result in distortion, a buffer (margin) of -6 dB is provided. Adjust the Mixer level as needed.
