|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent copy that was delivered within 12 hours and solved my problem.
 ;
I did not have the manual for a Whirl Pool gas dryer, therefore I purchased it from Owner-manuals. This is exactly what I needed. Thank you for the service.
;
I was so pleased to get the owner`s manuel within one hour! Thanks again.
Regards
Werner
;
Finding the owners manual for my Pioneer CRWM62R is greatly appreciated. I had searched several other web sites with no success. Although my manual was not listed on your site for immediate download, I recevied an email within a few hours that my ower's manual was posted for me. I had no difficulty downloading the manual for my 20 year old multi-cassette player. Owner Manuals provides a service that is valuable, easy-to-use, accurate , efficient, and priced fairly. I thank you.
;
Excellent manual - just what I needed. Although currently available only in German, their are lots of pictures which makes it all very clear.
Recording time code following the one last recorded on the tape
BR-DV6000 is equipped with a time code reader. When it enters the RECORD mode from the RECORDING PAUSE mode, it reads the time code data already recorded on the tape and continues recording time code from that value. (Regeneration)
TC/UB/CLOCK(1/2) Menu screen
� � � TC / UB / C LOCK T CG SOURCE T CG SE L EC T T CG MOD E NDF / DF ( NTSC ) DF B I T ( PAL ) TC DUP L I CATE TC OFFSET NEXT PAGE PAGE BACK ( 1 / 2 )� � � I NTERNA L REGEN REC - RUN ��� ON OFF OFF
:Setting:
� Set the TC/UB/CLOCK(1/2) Menu as follows.
TCG SOURCE TCG SELECT TCG MODE : INTERNAL : REGEN : No setting required. It will be in the same run-
ning mode as the tape. NDF/DF (NTSC) : No setting is required. It will be in the same frame mode as the tape.
:Operation:
1. Insert a tape with time codes recorded. 2. Set BR-DV6000 to the RECORDING PAUSE mode at the position where time codes are to be recorded again.
3. Press the PLAY button to go to the RECORDING mode.
Â¥ Time codes will be recorded on the tape, starting from where it stopped at last recording. The counter mode display shows either TCR or UBR.
Recording time code, input to the DV IN/OUT terminal
TC/UB/CLOCK(1/2) Menu screen
� � � TC / UB / C LOCK T CG SOURCE T CG SE L EC T T CG MOD E NDF / DF ( NTSC ) DF B I T ( PAL ) TC DUP L I CATE TC OFFSET NEXT PAGE PAGE BACK ( 1 / 2 )� � � I NTERNA L PRESET REC - RUN ��� ON AUTO OFF
:Setting:
Set the INPUT SELECT switch on the front panel to DV. Set TC DUPLICATE in the TC/UB/CLOCK(1/2) Menu screen to AUTO.
* To record time codes in the NON DROP frame mode from BRDV600 or GY-DV500, set TC DUPLICATE to NON DROP.
Memo
Time codes input to the TIME CODE IN terminal are ignored. Do not connect any device to the TIME CODE OUT terminal.
:Operation:
1. Check the time code of the DV input terminal.
Press the REC button when BR-DV6000 is in the STOP mode to display the time code on the monitor or the LCD. It will be displayed while the button is held down. The counter mode display shows DTCG or DUBG. 2. Select the RECORDING mode. ¥ Record time codes from the DV input terminal.
Memo
� For date/time also, data from the DV IN terminal are recorded. � When this terminal is connected to a D9 VCR, data/time data are not recorded.
61
|
|
|
> |
|
