|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Absolutely perfect! I've been trying to understand how to use all or at least some of the features of the receiver and especially the remote.
;
Copy of genuine owners/operators manual, very useful
;
The manual was a perfect match and was exactly what I was looking for. I'm very satisfied with my purchase.
;
Thank you for having the manual I needed for an older model Aiwa stero I had found on Ebay --- I wanted the Aiwa because I had tapes and cd's but I did not have a manual as to how to operate the system... I found what I needed and it has enabled me to set the system up for my enjoyment.
;
I wished detailed information of the JBL S310 and here I found it! Very happy with the service from this site!
BX-220H / BX-2115
The Rear Panel: 21
ThunderBass Amplifier
22 23
PREAMP OUT
EFFECTS LOOP
PWR AMP IN RETURN
27
SEND
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
26
AVIS:
RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
MODEL: SERIAL: LINE: WATTS:
BX-2215 BX2215PHD0312 120 V ~ 60 Hz 550 MAX
MADE IN THE U.S.A. BY SLM ELECTRONICS 1400 FERGUSON AVE. ST. LOUIS, MO 63133
S P E A K E R S
150W @ 8 OHMS 220W @ 4 OHMS MIN. LOAD
BALANCED LINE OUT
24 25
21. POWER CORD: Connect the male end of this cord to a properly grounded AC power outlet. Use only a grounded outlet! DO NOT defeat the ground pin of the cord! If the amplifier is used outside of the United States, see the area�s Crate dealer for the proper power cord or consult a local professional electrician. 22. PREAMP OUT: A pre-amplified line-level signal may be tapped from this jack for sending to an external amplifier, powered monitor, recording console, mixing board or effects processor. This is an unbalanced, mono 1/4� jack. 23. POWER AMP IN: A pre-amplified line level signal may be sent directly into the bass amp�s power amp (as when slaving two amplifiers together, for example). Connection to this jack interrupts the signal from the internal preamp to the power amp. The Preamp Out (#22) signal is not interrupted. 24. SPEAKERS: Use these jacks to connect the amp to your speaker cabinet(s). Use heavy-duty speaker cables with mono 1/4� plugs. These jacks are wired in parallel. Don�t use cabinet combinations resulting in impedance loads below 4 ohms. Use the chart below to help determine parallel loads. If in doubt, ask your dealer.
Cab Imp. 8 ohms 16 ohms 16 ohms # Cabs 2 2 4 Total Imp. 4 ohms 8 ohms 4 ohms
(#10). This signal is switchable to be either pre or post EQ through the front panel Pre/Post switch(#11). 26. EFFECTS LOOP SEND: This unbalanced jack lets you send a signal out to an external effects processor or tuner. The signal at this jack is post-EQ, pre-Master. Connect this to the input jack of the processor or tuner. 27. EFFECTS LOOP RETURN: This jack receives the signal from the output jack of an external effects processor. Use shielded cables with mono 1/4� plugs for connecting the Effects Loop.
25. BALANCED LINE OUT: Use this 3-pin XLR jack to send a line level signal to the house sound board or mixing console. The level of the signal at this jack is determined by the setting of the Line Out Level control on the front panel
5
|
|
|
> |
|
