|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I AM HIGHLY IMPRESSED BY THE EASE OF USE OF THIS DOWNLOAD SERVICE. INSTRUCTIONS ARE CLEAR AND SIMPLE TO FOLLOW....EVEN BY TECHNOPHOBES SUCH AS MYSELF. THE EMAILS POINT YOU IN THE RIGHT DIRECTION...ITS SO EASY PEASY. THE DOWNLOAD CHOICE OF USER MANUALS IS EXTENSIVE AND I COULD NOT FIND A CHEAPER OR MORE EFFICIENT SERVICE ON THE INTERNET. I COULD NOT HAVE MADE A BETTER CHOICE OF INFORMATION PROVIDER. SHOULD I EVER NEED ANOTHER USER MANUAL, THEN THIS IS THE FIRST CHOICE SITE. COULD NOT BE BETTER PLEASED!!!!!!!...MANY THANXES FROM JIM BURNS
;
I was impressed with the quality of service (frequent e-mails to let you know the status of your order), and the speed at which the download became available. The manual was a life saver and was not easy to track down. Thank you for such an excellent service.
;
the manual was just what i wanted it had all the revelent information required to operate the hifi .Iwould use any manual i downloaded for any item which needs a manual
;
Die gewünschte Bedienungsanleitung wurde vereinbarungsgemäß in deutsch bereitgestellt. Sie ist gut lesbar. Kein Kauderwelsch.
Danke für den Service.
;
GOOD SERVICE MANUAL GOT ALL THE INFO. THAT I NEEDED..
5- Recording CDs
Advanced recording
Setting the trigger level
The signal level which may be used with synchronized recording operations (here called the �trigger level� or �threshold�) is set as below: 1 With a recordable disc loaded, press the MENU key until the display shows: S_LVL> -XXdB, where -XX is the current value. 2 Turn the MULTI DIAL control or use the SKIP keys to change the value between -24, -30, -36, -42, -48, -54, -60, -66, and -72 dB (-60, -66 and -72 are only for digital signal). Low numerical values of this setting (towards �24) mean that it takes a louder signal to trigger the start of the synchronized recording. A high numerical value (towards �72) means that a relatively quiet signal will trigger the start of recording. When a digital source is selected, there is another option, DD, which means that any digital signal above the zero level will trigger the recording.
Using the trigger level
An input signal used as trigger to start recording is the sound level rises above the threshold for one second or more:
level Start of recording
S_LVL
If the �noise floor� is higher than the threshold, synchronized recording will not take place.
level Start of track is not registered
S_LVL
Noise level time
Noise is higher than threshold time
NOTE
Synchronized recording stops when the sound level drops below the threshold for five seconds:
level REC standby Five seconds
Remember that when recording from an analog source, the threshold should set so that it is higher than the �noise floor� such as the base level of hiss, pops and crackles which may come from an older vinyl recording, for example. However, synchronized recording is not recommended with the PHONO mode (see �Recording to disc from the RIAA PHONO inputs� on page 22).
S_LVL
time
If you set the threshold value so that only high-level signals trigger recording, remember that this will not record the start of a piece which has a slow fade-in:
level
S_LVL
Recording starts This part of the track may not be recorded
If you want to prevent the �five seconds� at the end of recording, try restricting the number of tracks using DD mode (see �Restricting the number of tracks� on page 22 and also �Automatic track division� on page 25). This will stop recording immediately so the �five seconds� will not be recorded. When there are no tracks left to be detected in DD mode, you need to make an extra track on the source media before recording.
Stop of recording
S_LVL
level time
S_LVL
Last track
Extra track time
TASCAM
CC-222MKIII
|
|
|
> |
|
