|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
FIRMWARE RENEWAL MODE
1. Turn the power on and press [SELECT] button on the remote control unit to put the TV/DVD into DVD mode. Then remove the disc on the tray. (It is possible to move to F/W version up mode only when the TV/DVD is in DVD mode with the tray open.) 2. To put the TV/DVD into F/W version up mode, press [9], [8], [7], [6], and [MODE] buttons on the remote control unit in that order. Fig. a appears on the screen.
"*******" differs depending on the models.
5. After programming is finished, the tray opens automatically. Fig. e appears on the screen and the checksum will be shown in (*2).
"*******" differs depending on the models.
F/W Version Up Mode VERSION : Completed SUM : 7ABC
Model No : ******* VERSION : *.** ************.***
(*2)
F/W Version Up Mode
Model No : ******* VERSION : *.**
Please insert a DISC for F/W Version Up.
Fig. e Completed Program Mode Screen
6. 7.
EXIT: SELECT
Fig. a Version Up Mode Screen
8. 9.
The TV/DVD can also enter the version up mode with the tray open. In this case, Fig. a will be shown on the screen while the tray is open. 3. Load the disc for version up. 4. The TV/DVD enters the F/W version up mode automatically. Fig. c appears on the screen. If you enter the F/W for different models, �Disc Error� will appear on the screen, then the tray will open automatically.
"*******" differs depending on the models.
At this time, no button is available. Remove the disc on the tray. Press [CH. o / p] button on the unit to go to TV mode, or press [STANDBY-ON] button on the unit to turn the power off. Press [SELECT] button on the remote control unit to put the TV/DVD into DVD mode again. Press [1], [2], [3], [4], and [DISPLAY] buttons on the remote control unit in that order. Fig. g appears on the screen.
"*******" differs depending on the models.
MODEL : ******* Version : *.** Region : *
F/W Version Up Mode VERSION : (*1) Reading...
Model No : ******* VERSION : *.** ************.***
EEPROM CLEAR : CLEAR
EXIT: SELECT
Fig. g
10.Press [CLEAR] button on the remote control unit. Fig. h appears on the screen.
"*******" differs depending on the models.
Fig. c Programming Mode Screen
The appearance shown in (*1) of Fig. c is described as follows:
No. 1 2 3 Appearance Reading... Erasing... State Sending files into the memory Erasing previous version data
MODEL : ******* Version : *.** Region : * EEPROM CLEAR : OK
EEPROM CLEAR : CLEAR
EXIT: SELECT
Programming... Writing new version data
Fig. h
When �OK� appears on the screen, the factory default will be set. Then the firmware renewal mode is complete. 11.To exit this mode, press [CH. o / p] or [SELECT] button to go to TV mode, or press [STANDBY-ON] button to turn the power off.
8-1
P7401FW
|
|
|
> |
|
