GEMINI CD-2000X
Owner's Manual

To clear your sample simply hold the STOP BUTTON (4) down for 3 seconds or more. *Note: your sample will remain in the memory until you either clear it or create a new sample. You may change CDs and still use the sample you created previously. RELOOP/STUTTER (12) - Used for repeated play (stutter) from the cue point, repeating a previously set loop. The reloop function automatically returns the music to the cue point and will play the loop until it is released with the CUE B/EXIT BUTTON (11). CD starts instant play from the previously set cue points. CUE BUTTONS - The CD-2000X allows you to set up to 5 different cue points using the CUE BUTTONS (25). To set each individual cue point, press the MEMO BUTTON (26) and then a cue button (Cue 1-5). You can keep setting cue points up to 5. As your music is playing, if you would like it to jump to one of your set cue points, simply press that individual cue button (Cue 1-5) and the music will jump to that point. BOP BUTTON - When you set a cue point using the CUE BUTTON (16) or FLY CUE BUTTON (10A) you can return to that cue point at any time during the musical performance simply by pressing the BOP BUTTON (7). The music will immediately return to that point. BPM/PITCH BUTTON - The BPM/PITCH BUTTON (37) enables you to adjust the beats per minute of the music either automatically or manually. Press the BPM/PITCH BUTTON (37) to activate the automatic BPM control. To switch to manual operation, press and hold the BPM/PITCH BUTTON (37) for 3 seconds. Then tap the button in the tempo of your choice and the music will set itself to that tempo.

2. Press the OPEN/CLOSE BUTTON (27), place a CD in the DISC TRAY (20) and press the OPEN/ CLOSE BUTTON (27) again. The tray will close into the unit. 3. Push the TRACK SKIP +10 BUTTONS (13) to select the track you want to play. 4. Press the PLAY/PAUSE BUTTON (17) and the unit will instantly play.

CUE INSTRUCTIONS
To use FLY CUE (10A) to set a cue point, follow these instructions: 1. With the unit in the play mode (play/pause LED glows green), press FLY CUE (10A) at the point where you want the cue point to be (the unit will continue to play). The cue point is now memorized. Press the CUE BUTTON (16) to return to the memorized cue point. Push the PLAY/PAUSE BUTTON (17), and the unit will instantly play from the spot selected. 2. Press FLY CUE (10B) to memorize a cue point as music is playing. You can use FLY CUE (10B) to create a loop using FLY CUE (10B) and the B/ EXIT BUTTON (11). AND/OR 1. To memorize the spot at which you want play to start, select the proper track, and then push the PLAY/PAUSE BUTTON (17) so the unit goes into the play mode (play/pause LED will glow green). Listen to the CD and when the CD gets to the approximate spot, push PLAY/PAUSE (17) so the unit goes into pause mode (play/pause LED will blink green). Move the JOG WHEEL (9) to the precise spot you want play to begin and push the PLAY/PAUSE BUTTON (17) to memorize the cue point. Press the CUE BUTTON (16) to return to the memorized cue point. Push the PLAY/PAUSE BUTTON (17), and the unit will instantly play from the spot selected. 2. To fine tune a cue point, pause play at the memorized cue point (the cue LED will glow and the play/ pause LED will blink), then use the JOG WHEEL (9) to scan frame by frame (1/75th of a second) to where you want play to begin (the cue LED will blink while you scan). Press PLAY/PAUSE (17) to save the new cue point.

OPERATING INSTRUCTIONS
1. Make sure that the VOLTAGE SELECTOR switch (30), found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER BUTTON (21). The unit will turn on. Pushing the POWER BUTTON (21) a second time will turn the unit off.

Page 6