|
|
|
Who's Online
There currently are 5985 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
;
I received the Manual in a timely manner and it was exactly what I needed.
This is a perfect copy of the Service Manual, The quality is great. I am very
happy. Thank you
;
exactly as they say. Within 24 hours the link to the pages and offcourse it was the right service manual. Super and thanks
 ;
The manual was exact the thing that was promised. My old car stereo is working again thanks to the information supplied.
THEORY OF OPERATION
The E and F signals are amplified and subtracted. This produces the tracking error signal TEAO (U501, pin 7 ). The F channel�s gain is adjusted by E-F balance potentiometer R506. The TEAO signal is used by the anti-shock circuit, the track jump detection circuit, and the tracking servo. The track jump detection output is sent to U502 on the TES line (U501, pin 47). R510, which is connected to TPA+ (U501, pin 13 ), adjusts the tracking gain. This signal is amplified and filtered. It then appears as an output on TPAO (U501, pin 15). R511 adjusts the tracking offset . The TPAO signal is further amplified and filtered. It then appears as an output on TDO (U501, pin 21). This signal is fed to U503. U503 generates the complementary outputs (U503) that are used to actuate the tracking coil (P502, pins 6 and 7). The TDO signal is also used as the input for the sled servo. This signal is filtered and fed to the sled servo amplifier on SLEQ (U501, pin 20). This signal is amplified and is then added to the FEED signals from U505. The result appears on SLDO (U501, pin 33). This signal is fed to U504. U504 generates the complementary outputs (pins 11 and 14) that are used to drive the sled motor (P503, pins 5 and 6). The Constant Linear Velocity (CLV) servo is regulated by comparing the playback speed to a FIXED reference frequency in U502. The error signal appears at U502, pins 10 and 11 (CLV+ and CLV-). These signals are subtracted and the difference appears on SPD (U501, pin 29). The SPD signal is filtered and amplified. It then appears at the output on SPDO (U501, pin 31). This signal is fed to U504. U504 generates the complementary outputs (pins 3 and 6) that are used to drive the disc motor (P503, pins 1 and 2). U501 regulates the laser power by monitoring the MD input (P502-3). This signal is compared to a reference to generate the proper drive signal on LDD (U501, pin 74). This signal biases Q501. Q501 drives the laser diode output LD (P502-1). U501�s main DC reference voltage is Vref3 which appears on pin 9. This voltage is nominally 4V. The VCO is the final function contained in U501. The VCO is used by U502 for EFM demodulation. The PDO output signal (U502, pin 4) is filtered and amplified by U501. In turn, this output appears on VCOC (U501, pin 59) This is the VCO control voltage input. The nominal VCO free-run frequency is 8.64MHz and is set by R558. The VCO also requires a 16.9344MHz clock input from U502. This input appears on CLK (U501, pin 62). The VCO output appears at VCOO (U501, pin 60). This signal is buffered by U502. The buffered output appears on AO (U502, pin 2). The VCO output is divided by 2 in U502. In turn, its output appears on PCK (U502, pin 18), which is 4.32MHz. The DSP clock is derived from a 16.9344MHz crystal oscillator (X501). However, this oscillator is normally turned off by U505. It is only switched on during focusing and when a disc is playing. U502 receives its EFM input from U501 on EFMIN (pin 8). This signal is sliced, EFM demodulated, and CIRC decoded. The digital audio output signal is sent serially to U506 on the LRCLK, DFOUT and DACLK lines (U502, pins 33, 35, and 36). U502 receives servo control commands from U505 on the serial bus (U502, pins 51, 53 and 54). These commands are translated to appropriate control signals for U501 for focusing, disc start, disc stop, disc braking, and track jumps. The focus servo is controlled by the FOCS and FST outputs. The CLV servo is controlled through the CLV+ and CLV- lines. The tracking servo is controlled by the TOFF, TGL, and THLD outputs. Track jumps are created by signals on the JP+ and JP- lines. Track jump detection is based on signals from U501 on the HFL and TES inputs. 15
|
|
|
> |
|
