|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
For five bucks you can barely buy a hamburger. Or for the same five bucks you can buy a service manual. Much more useful. (and better for your health, depending on where you buy your hamburgers).
Yes, there are free manual sites out there, but if they don't have what you want, you have to pay.
And five bucks isn't much. Not for full specs, schematics and adjustment and parts replacement procedures.
My only criticism is that grayscale illustrations aren't well rendered, but I've seen worse.
Schematics and text are clear.
I'll be happy to purchase from here again.
Mike
[email protected]
 ;
Impressively thorough. Even the simple operators manual helped me "fix" one of the 2 CD players in the unit. This unit reads CD's from the top so they should be installed in the magazines "upside down" from typical CD players. The CD player service manual helped me unjam a stuck carriage because somebody transported the box laying down loaded with CD's. A little lens cleaning & the player now works well! Thanks for you help at a great price! Joe
 ;
I was skeptical at first but later found the manual to be good quality for the price. It took a couple hours to receive the email with the download link, well worth the wait. Thanks.
 ;
very helpful, I could not have cleaned motherboard and replaced the main fan without it
 ;
Good manual, schematics nice and clear with good quality scanning. Woul dhave been nice to have immediate access after purchasing though.
SETTING CLOCK RESETTING THE MICROCOMPUTER
ditions:
q To erase all of the stored memory contents (clock and timer q If the display is not correct. q If the operation is not correct. Within 5 seconds, press the MEMORY/SET button. settings, tuner and CD presets). Press the CLOCK button.
(Main unit operation)
In this example, clock is set for the 24-hour (0:00) system. Reset microcomputer under the following con-
1 Press ON/STAND-BY button to enter the stand-by mode.
CD-BA3000H
2
4 Press TUNING/TIME ( or ) button to select the time 2
(0:00 23:59) least 1 second. q �CLEAR AL� will appear. �AM 0:00� �The 12-hour display will appear. (AM 0:00 PM 11:59) Caution: (AM 12:00 PM 11:59) memory including clock timer settings, tuner and DEMO button, hold down the ON/STAND-BY button for at �0:00� �The 24-hour display will appear.
3 1 Press ON/STAND-BY button to enter the stand-by mode.
display mode. Whilst pressing down button and the X-BASS/
�AM 12:00� �The 12-hour display will appear. q The operation explained above will erase all data stored in
q Note that this can only be set when the unit is first inCD presets.
stalled or it has been reset.
5 Press the MEMORY/SET button.
PREPARATION FOR USE 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to ad-
vance the time by 1 hour. Hold it down to advance cons Remote control tinuously.
q When the 12-hour display is selected, �AM� will change
automatically to �PM�.
Press the MEMORY/SET button.
7 8
0.2 6 m q Exposing sensor on the main unit to strong light may (8" 20�) interfere with operation. Change lighting or the direction
Notes concerning use: q Replace batteries if the operating distance is reduced or if the operation becomes erratic. q Periodically clean transmitter LED on the remote control and sensor on the main unit with a soft cloth.
Press TUNING/TIME ( or ) button to adjust the min-
of the unit. q Keep the remote control away from moisture, excessive heat, shock, and vibrations.
OPERATION MANUAL
�6�
utes. q Press the TUNING/TIME ( or ) button once to advance time by 1 minute. Hold it down to change the time in 5 minute intervals. q The hour setting will not even if minutes advance from �59� to �00�.
9 Press the MEMORY/SET button.
q The clock starts operating from �0� second.
(Seconds are not displayed.) And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button. q The time display will appear for about 5 seconds.
Note: q The clock display will flash on and off at push of the CLOCK button when the AC power supply is restored after a failure occurs or after the AC power lead is disconnected. If this happens, follow procedure below to change the clock time.
To change the clock time:
1 Press the CLOCK button.
2 Within 5 seconds, press the MEMORY/SET button.
3 Perform steps 6 9 above.
To change the time display mode:
Perform steps 1 2 in the section �RESETTING THE MI-
CROCOMPUTER�.
2 Perform steps 1 9 above.
|
|
 |
> |
|