|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent manual including schematics. The service was great and the manual helped complete the job.
;
It was magic after so many years to still be able to source this info. It was equally amazing to return my Pioneer receiver to it near new sound quality AFTER NEARLY 30 YEARS! Thank you for this ability!
;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
 ;
Easy and secure way to get a complete service manual of a vintage hifi component. Only some parts of the print copy are dificult to read. Nice price!
;
The manual is an excellent reproduction with complete schematics, made troubleshooting and repair a simple process.
SETTING CLOCK RESETTING THE MICROCOMPUTER
EQUALIZER q To erase all of the stored memory contents (clock and timer (Main unit operation) tem. X-BASS/ settings, tuner and CD presets). DEMO q If the display is not correct.
Reset microcomputer under the following conditions: In this example, clock is set for the 12-hour (AM 12:00) sys-
q If the operation is not correct.
MEMORY/SET
POWER Within 5 seconds, press the MEMORY/SET button. ON/
1
Press ON/STAND-BY button to enter the stand-by mode.
2 Press the CLOCK button. 1 Press ON/STAND-BY button to enter the stand-by mode. 3 2
ON/ BASS/DEMO button, hold down the ON/STAND-BY button for STAND-BY at least 1 second. Press TUNING/TIME ( or ) button to select the time
POWER STAND-BY While pressing down button and the EQUALIZER/X-
4
(AM 12:00 PM 11:59) Caution: TIME (AM 0:00 PM 11:59) memory including clock timer settings, tuner and CD
presets. "0:00" � The 24-hour display will appear.
display mode. q "CLEAR AL" will appear.
CLOCK "AM 12:00" � The 12-hour display will appear. TUNING/
"AM 0:00" � 12-hour display appear. q The operation explained above will erase all data stored in ( ) (0:00 23:59)
q Note that this can only be set when the unit is first installed
or it has been reset (see page 15).
2
5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance
the time by 1 hour. Hold it down to advance continuously.
q When the 12-hour display is selected, "AM" will change auto-
matically to "PM".
3
4 minutes.
7 Press the MEMORY/SET button. 8 Press TUNING/TIME ( o r ) button to adjust the
OPERATION MANUAL
�5�
q Press the TUNING/TIME ( or ) button once to advance
q The hour setting will not even if minutes advance from
by 1 minute. Hold it down to change the time in 5 minute intervals. 12:00 AM 0:00
"59" to "00".
q The clock starts operating from "0" second.
9 Press the MEMORY/SET button. 5
(Seconds are not displayed.) And then the clock display will disappear after a few seconds.
To see the time display:
Press the CLOCK button.
q The time display will appear for about 5 seconds.
6
Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power
failure occurs or after the AC power cord is disconnected.
7
If this happens, follow procedure below to change the clock time.
To change the clock time:
8 xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button.
9 zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE
MICROCOMPUTER", on page 15.
CD-BA120/125
yPerform steps 1 9 above.
|
|
|
> |
|
