|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very,very good manual.It was very explicit and readble.It was helpfull.Thanks.
;
The service manual is scanned, but high quality, high resolution. The smallest texts on schematics diagram is readable. Super! Thank you!
;
I am satisfied with the service. And if need another manual, i will definitely buy from this site. Keep up the good work.
;
have download a number of manuals todate , most are excellant, one or two sometimes a little difficult to read but a least avaialable, great site .
Brad.
;
Excellent had everything I wanted, very happy with purchase
SETTING THE CLOCK REMOTE CONTROL
Replace batteries if the operating distance is reduced tem. the hour. or if the operation becomes erratic. trol and sensor on the main unit with a soft cloth. Exposing sensor on the main unit to strong light may interfere with operation. Change lighting or the direc-
In this example, clock is set for 24-hour (0:00) sysPress the TUNING/TIME ( or ) button to adjust Notes concerning use:
6
CD-BA1300H
(Main unit operation) Periodically clean transmitter LED on the remote con-
Press the TUNING/TIME ( or ) button once to tion of the unit. time by 1 hour. Hold it down to advance con0.2 6 m Keep the remote control away from moisture, excessive ON/ tinuously. heat, shock, and vibrations.
(8" 20') When the 12-hour display is selected, "AM" will change
STAND-BY
1 5 Press the MEMORY/SET button. 1
automatically to "PM".
CLOCK
7
MEMORY/SET
TUNING/TIME ( )
8 Press the TUNING/TIME ( or ) button to adjust
the minutes.
1 Press ON/STAND-BY button to enter the standRESETTING THE MICROCOMPUTER
by mode.
2 Press the CLOCK button.
OPERATION MANUAL
�6�
9 Press the MEMORY/SET button. EQUALIZER timer settings, tuner and CD presets). ON/
Press the TUNING/TIME ( or ) button once to advance time by 1 minute. Hold it down to change the time in 5-minute intervals. Reset microcomputer under the following condiThe hour setting will not advance even if minutes tions: advance from "59" to "00". Within 5 seconds, press MEMORY/SET button. To erase all of the stored memory contents (clock and
3
X-BASS/ If the display is not correct. DEMO If the operation is not correct. STAND-BY
1 Press ON/STAND-BY button to enter the stand-
4 Press TUNING/TIME ( or ) button to select the The clock starts operating from "0" second. (Seconds are 2 Whilst pressing down / button and the
by mode.
time mode. not displayed.) And then clock display will disappear EQUALIZER/X-BASS/DEMO button, hold down the
"CLEAR AL" will appear.
after a few seconds. ON/STAND-BY button for at least 1 second.
To see the time display: Press the CLOCK button. Caution: The time display will appear for about 5 seconds. The operation explained above will erase all data stored
in memory including clock timer settings, and tuner 0:00 AM 12:00
Note:
"0:00" The 24-hour display will appear. a failure occurs or after the AC power lead is
and CD presets. The clock display will flash on and off at push of the CLOCK button when the AC power supply is restored
disconnected. If this happens, follow the procedure below (0:00 23:59) to change the clock time.
"AM 0:00" The 12-hour display will appear.
(AM 0:00 PM 11:59) 1 Press the CLOCK button.
To change the clock time:
2 Within 5 seconds, press the MEMORY/SET button. "AM 12:00" The 12-hour display will appear. 3 Perform steps 6 9 above.
(AM 12:00 PM 11:59)
To change the time display mode:
Note that this can only be set when the unit is first Perform steps 1 2 in "RESETTING THE MICROCOMinstalled or it has been reset. PUTER".
Press the MEMORY/SET button.
2 Perform steps 1 9 above.
5
|
|
|
> |
|
