|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Incredibly clear!!!! Well done, complete and wonderful. It could not better than this!!!!
 ;
Thank You for fast delivery for the sheme.
Everything allright.
Thanks & best regards Franz
;
again you did a very good job. It was fast too. Photocopy are really readable and clear
;
Probably it never existed a 1081 official service manual from Commodore, it's look more like a NAPCEC service manual & diagrams compilation of the 1084 series and his variants, like the nap6523, 8cm505, 1084S, 1084P and obviously the 1081. It's more complete than other scans and the quality of the scans also are far superior. It has two circuit diagrams variants of the 1081, mono and stereo versions. It doesn't include a diagram for the Philips CM8500 or CM8501, they look like the 1081 but they are slightly different.
;
Rapid, clear well done as all the scheme I downloaded from this site. Great job very functional and very useful
CD-BK100W/CD-BP90W
DISASSEMBLY
Caution on Disassembly Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance: 1. Take cassette tape and compact disc out of the unit. 2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit. 3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling. 4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing. CD-BK100W/CD-BP90W
STEP 1 2 3 REMOVAL Top Cabinet Side Panel (Left/Right) CD Tray Cover/ CD Player Unit PROCEDURE 1. Screw ...................... (A1) x4 1. Screw ...................... (B1) x8 FIGURE 10-1 10-1 Note 1: How to open the changer manually. (Fig. 11-1) 1. In this state, turn fully the lock lever in the arrow direction through the hole on the loading chassis bottom. 2. While holding the lock lever, rotate the cam gear anticlockwise until the cam gear rib engages with the clamp lever. (Fig. 11-2) 3. After that, push forward the slide chassis. Note 2: 1. After removing the connector for the optical pickup from the connector, wrap the conductive aluminium foil around the front end of the connector so as to protect the optical pickup from electrostatic damage. Note 3: 1. Be careful not to break the claw of the CD mechanism. 2. When fining back the cam gear assembly, let it lock by front movement.
CD-BK100W/CD-BP90W Illustration: CD-BK100W
(A1)x2 ø3x12mm Top Cabinet
1. Turn on the power supply, .. 10-2 open the disc tray, take out the CD tray cover, and close. (Note 1) 2. Hook ........................ (C1) x3 3. Screw ...................... (C2) x1 4. Hook ........................ (C3) x2 5. Socket ..................... (C4) x2 1. Screw ...................... (D1) x6 1. Flat Cable ............... 2. Socket ..................... (For CD-BK100W) 2. Socket ..................... (For CD-BP90W) 3. Tip ........................... 4. Screw ...................... 5. Hook ........................ (E1) x1 (E2) x4 (E2) x3 (E3) x1 (E4) x3 (E5) x2 11-3 10-2 11-3
Side Panel (Right) (B1)x2 ø3x7mm (A1)x2 ø3x12mm (B1)x2 ø3x10mm (B1)x2 ø3x7mm CD-BK100W Rear ONLY Panel (B1)x2 ø3x7mm Side Panel (Left)
4 5
Rear Panel Front Panel
6 7 8 9 10 11 12
Main PWB
1. Socket ...................... (F1) x2 2. Screw ....................... (F2) x7
Figure 10-1
11-4 11-4 11-4 11-4
(C3)x1 CD Servo PWB (C4)x2 1 CD Tray Cover (C1)x3
Mic PWB 1. Screw ...................... (G1) x1 (CD-BK100W Only) 2. Bracket .................... (G2) x1 Display PWB 1. Screw .................... (H1) x11 2. Flat Wire .................. (H2) x1 Headphones PWB 1. Screw ....................... (J1) x1 2. Bracket ..................... (J2) x1 Tape Mechanism 1. Open the cassette holder. .. 2. Screw...................... (K1) x6 Turntable Disc Tray 1. Hook ......................... (L1) x2 2. Cover ....................... (L2) x1 1. Turn fully the lock lever in the arrow direction. 2. While holding the lock lever,rotate the cam gear until the cam gear rib engages with the clamp lever. 3. Push the slide chassis backward to engage the claw with the groove and remove it in the direction of the arrow. . (M1) x6 1. Screw ...................... (N1) x1 2. Socket ..................... (N2) x4 3. Hook ........................ (N3) x2 1. Hook ........................ (P1) x2 2. Hook ........................ (P2) x3
11-5 11-1 11-2
Pull Pull
1 2
Rear Panel (C2)x1 ø3x10mm
CD Player Unit (C3)x1
11-6
13
CD Servo PWB (Note 2) CD Mechanism
12-1
CD-BK100W ONLY (D1)x1 ø3x7mm
14
12-2
(D1)x5 ø3x10mm
Figure 10-2
� 10 �
|
|
|
> |
|
