|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This manual is very useful. Because pioneer sx-q180 is unhandy to use without manual.
;
Manual was destroyed and this purchase made it possible to recover my manual . It was easy to down load and smooth to use thanks .
 ;
Turns out this was not the manual i was looking for. The concertmate 670 keyboard i have is a "Realistic" model made for Radio Shack and none of the diagrams on the owners manual i received matches up. HOWEVER, I must say the service Owners Manual provides was fast and efficient by being available online. The manual was in good readable condition and easily downloaded.
;
Great price, Quick delivery, the document was very usefull A+++++++++++++++
;
Thank´s for your help, I already recived these manual from you
Adjusting sound
You can select the following modes for adjusting sound depending on the music you listen to: BASS (low frequencies), TRE (high frequencies), BAL (left/right), FAD (front/ rear) and H-BASS (high bass).
Setting the clock
1 Press and hold DSPL until the clock indicator
flashes in the display. 2 Press + (to set hour) or � (to set minute), and then turn Jog dial. 3 Press DSPL.
1 Press SEL repeatedly to select the mode to be
adjusted. Pressing SEL cycles through the modes. The selected mode�s indicator appears. 2 Turn Jog dial to increase/decrease the level or to select on/off for the selected mode.
Displaying the clock
1 Press DSPL. To return to the former display, press DSPL again.
Note
Adjust the level or select on/off within 5 seconds, or the selected mode will return to previous state.
RADIO OPERATION
Tuning in to a station
(Seek/Manual Tuning)
LO
Aligning the source levels
(Source Level Adjuster)
Volume may vary each time you change the source mode. In this case, you can align each source mode�s volume to almost the same level. 1 Press Jog dial (PUSH-SOURCE) or TU (TUNER) repeatedly to select the desired mode. 2 Press DSPL while pressing SEL. �LA 0� appears on the display. 3 Turn Jog dial to adjust the level.
+/�
TU (TUNER) Local indicator Stereo indicator
Note
Adjust the level within 5 seconds, or the selected mode will be canceled.
Restoring the factory settings
1 Turn off the unit. 2 Press and hold DSPL until �LA --� appears on the
display. Band indicator Frequency indication TUNER indication
1 Press TU (TUNER) repeatedly to select the desired
band (FM1, FM2, FM3, AM1, or AM2).
Note
You can restore the factory settings only for VOL, BASS, TRE, BAL, FAD, and H-BASS, and aligned source volume levels.
2* Press + (to move to higher frequencies) or � (to
move to lower frequencies) to tune in to a station. �STEREO� appears on the display when an FM station is broadcasting in stereo, and receiving conditions are good. *Seek Tuning and Manual Tuning � Press and hold + or � until seek Tuning starts. The unit locates a station automatically (Seek Tuning). � Press + or � repeatedly to search for a desired station while increasing or decreasing the frequency step by step (Manual Tuning). To stop Seek Tuning, press + or � again.
Setting the beep tone
1 Turn off the unit. 2 Press and hold SEL until �bEEP� appears on the
display.
3 Turn Jog dial to select on (level indicators appear)
or off (level indicators disappear).
4 Press SEL.
3
ENGLISH
 $4.99 CDCX437 AIWA
Service Manual Complete service manual in digital format (PDF File). Service manuals usually contains circuit diagr…
|
|
|
> |
|
