|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was exactly what I needed, Good quality scans too. superb.
;
I am so happy found this site as it consists of so many Manuls and easy to aquire. This onei s exactly what I wanted and much more as it has info on not only how to use the tuner but how to repair it as well. I will come here 1st before purchasing else where! Thanks owner-manual.com!
;
Top class product, I printed it out on A3 paper and it is clear and very easy to follow.
Cheaper than buying a new radio!
;
is part of the manual is very useful for repairing
Here are circuit diagrams
if there is damage, I recommend using this part of the
a complete list of circuit boards and components
 ;
Hello.
This paper enable me, to bring this lovley Scope into Function.
Without this Page, i have no cance to make this finish.
Hans M. Knoll Germany
CD-E100H CD-E100E
REMOVING AND REINSTALLING THE MAIN PARTS
TAPE MECHANISM SECTION
Perform steps 1 to 6 and 9 of the disassembly method to remove the tape mechanism.
(A1)x1 ø2x7mm Hook (A2)x2
TAPE 1
(A1)x1 ø2x3mm Record/Playback Head
How to remove the record/playback and erase heads (TAPE 1) (See Fig. 7-1)
1. When you remove the screws (A1) x 2 pcs., the record/ playback head can be removed. 2. Move the hooks (A2) x 2 pcs., toward the center position as shown in Fig. 7-1 and then lift the erase head.
How to remove the playback head (TAPE 2) (See Fig. 7-2)
1. When you remove the screws (B1) x 2 pcs., the playback head can be removed.
Erase Head
Figure 7-1
How to remove the pinch roller (TAPE 1) (See Fig. 7-3)
1. When you remove the screw (C1) x 1 pc., the pinch roller can be removed. Note: When installing the pinch roller, pay attention to the spring mounting position.
(B1)x1 ø2x6mm
(B1)x1 ø2x6mm
TAPE 2
Playback Head
How to remove the pinch roller (TAPE 2) (See Fig. 7-3)
1. When you remove the screw (D1) x 1 pc., the pinch roller can be removed. Note: When installing the pinch roller, pay attention to the spring mounting position.
Figure 7-2
TAPE 1
(C1)x1 ø2x4mm
TAPE 2
(D1)x1 ø2x4mm
How to remove the tape motor (See Fig. 7-4)
1. Remove the belt. 2. Remove the screws (E1) x 6 pcs., to remove the motor bracket. 3. Remove the screws (E2) x 3 pcs., to remove the tape motor.
Pinch Roller
Pinch Roller
How to remove the belt (TAPE 1) (See Fig. 7-5)
1. Remove the main belt (F1) x 1 pc., from the tape motor side. 2. Remove the FF/REW belt (F2) x 1 pc.
Tape Motor
Figure 7-3
(E1)x2 ø2x4mm (E1)x2 ø2x4mm
How to remove the belt (TAPE 2) (See Fig. 7-5)
1. Remove the main belt (G1) x 1 pc., from the tape motor side. 2. Remove the FF/REW belt (G2) x 1 pc.
(E1)x2 ø2x4mm
Tape Motor TAPE 2 Main Belt (G1)x1 FF/REW Clutch Ass'y Tape Motor TAPE 1 Main Belt (F1)x1
Motor Bracket
TAPE 2
Main Belt (G1)x1
(E2)x3 Special Screw
TAPE 1
FF/REW Belt (F2)x1 FF/REW Clutch Ass'y FF/REW Belt (G2)x1 Main Belt (F1)x1
Motor Bracket
Tape Motor
Figure 7-4 �7�
Figure 7-5
|
|
|
> |
|
