|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thanks for offering this item at such a good price. Proved handy in identifying the part I was looking for my set.
Thanks again.
;
This is the original manufacturers service manual, with detailed info on the circit boards, explosion drawings of all parts in assembly order, and tuning instructions. The only thing missing is the information on the dimensions of the various drive belts. mail me if you need them. gcrossman_at_aol.com
;
Ordered service manuel for a hard to find plasma tv - your company made it easy to find and purchase - I will use you again
Thanks for your help
 ;
This is a high quality manual with clear schematic and components layout diagrams ; with service procedure included.
;
This service manual for the Kenwood KT-990D was reproduced really well ,is very legible and manual is complete.Combined with the low price paid,in the future,I will be checking Owner-Manuals.com any time I need a manual.
SETTING CLOCK RESETTING THE MICROCOMPUTER
Reset microcomputer under the following conditions:
(Main unit operation) Press ON/STAND-BY button to enter the stand-by mode. q To erase all of the stored memory contents (clock and timer
2 1 Press ON/STAND-BY button to enter the stand-by mode. 4 Press TUNING/TIME ( or ) button to select the time
Whilst pressing down button and the second.
(AM 0:00 PM 11:59) STAND-BY
In this example, clock set for q If the display is not correct. 24-hour (0:00) system. Within 5 seconds, press MEMORY/SET button. q If the operation is not correct.
Press the CLOCK button.
1 2 settings, tuner and CD presets).
3
button, hold down the ON/STAND-BY button for at least 1 CLOCK
1,2
2
display mode. "0:00" � The 24-hour display will appear.
ON/ "AM 0:00" � The 12-hour display will appear. TUNING/ TIME ( )
(0:00 23:59)
q The operation explained above will erase all data stored in q Note that this can only be set when the unit is first installed memory including clock timer settings, tuner and CD SET
"AM 12:00" � The 12-hour display will appear. (AM 12:00 PM 11:59) MEMORY/
Caution:
or it has been reset (see page 29). presets.
5 Press the MEMORY/SET button. 6 Press TUNING/TIME ( or ) button to adjust the hour.
q Press the TUNING/TIME ( or ) button once to advance
2 q When the 12-hour display is selected, "AM" will change autoNotes concerning use: the operation becomes erratic. 0.2 6 m minutes. and sensor on the main unit with a soft cloth. (8" 20')
the time by 1 hour. Hold it down to advance continuously. s Remote control
matically to "PM".
7 Press MEMORY/SET button. q Replace batteries the operating distance is reduced or if 8 Press TUNING/TIME ( o r ) button to adjust q Periodically clean transmitter LED on the remote control 3
4 Press TUNING/TIME ( or ) button once advance q Exposing sensor on the main unit to strong light may in1 5
by 1 minute. Hold it down to change time in 5 terfere with operation. Change lighting or the direction of minute intervals. the unit. 1
OPERATION MANUAL
�7�
0:00 AM 12:00 The hour setting will not even if minutes advance q Keep the remote control away from moisture, excessive heat,
"59" to "00". shock, and vibrations.
q The clock starts operating from "0" seconds.
9 Press the MEMORY/SET button. 5
(Seconds are not displayed.)
6
To see the time display:
7
Press the CLOCK button. q The time display will appear for about 5 seconds.
Note: q The clock display will flash on and off at push of the CLOCK button when the AC supply is restored after a power failure occurs or after the AC power lead is disconnected. If this happens, follow procedure below to change the clock time.
8
9
To change the clock time:
xPress the CLOCK button. yWithin 5 seconds, press the MEMORY/SET button. zPerform steps 6 9 above.
To change the time display mode:
xPerform steps 1 2 in the section "RESETTING THE MICRO-
COMPUTER", on page 29.
CD-PC671H/651H
yPerform steps 1 9 above.
|
|
|
> |
|
