|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
SECTION 6 DIAGRAMS
6-1. CIRCUIT BOARDS LOCATION THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS. (In addition to this necessary note is printed in each block.)
For schematic diagrams. Note:
� All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics and tantalums. � All resistors are in � and 1 /4 W or less unless otherwise specified. � % : indicates tolerance. � ¢ : internal component. � 2 : nonflammable resistor. � 1 : fusible resistor. � C : panel designation. Note: The components identified by mark ! or dotted line with mark ! are critical for safety. Replace only with part number specified. � � � � � U : B+ Line. V : B� Line. H : adjustment for repair. Voltages and waveforms are dc with respect to ground under no-signal (detuned) conditions. Voltages are taken with a VOM (Input impedance 10 M�). Voltage variations may be noted due to normal production tolerances. Waveforms are taken with a oscilloscope. Circled numbers refer to waveforms. Signal path. J : CD c : DIGITAL OUT
45MHz 16.9344MHz (PLAY)
� Waveform
1
TP1 (RF)
1.5Vp-p
KEY board POWER SW board SERVO board
2
CN304 !¡
2.7Vp-p
3
IC301%¢ (128FSO)
4.0Vp-p
HP board
5.6448MHz (128Fs)
ROTARY SW board MAIN board DISP board
� � �
4
IC301@� (XOUT)
4.8Vp-p
For printed wiring boards. Note:
� X : parts extracted from the component side. � ® : Through hole. � ¢ : internal component. � b : Pattern from the side which enables seeing.
5
IC801#ª (EXTAL)
POWER board
4.0Vp-p
TRANS board
8MHz
LOADING board
SLED board SPINDLE board LD IN SW board
� 13 �
� 14 �
|
|
|
> |
|
