|
Who's Online
There currently are 5965 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Exactly the JVC service manual and schematics that I was looking for - delivered just hours after order. Will do business again!
;
This is a fantastic site, ad I have been a returning satisfied cusumer!
Thanx for a great sevice!
;
Je suis audiophile belge, électronicien et créateur d'enceintes acoustiques.
J'ai apprécié la qualité des documents fournis. Ils sont très lisibles, ils peuvent être agrandis sans problème et ils sont complets. Pour moi, c'est parfait. Pour cette qualité, je suis d'accord de payer. Et le système de paiement et d'envoi est simple. Merci, continuez comme cela.
Frédéric
;
The cover page was a little scary, very dark but readable. The remainder of the document was better copy and easily readable. Why would I give 5 Stars? (1) PRICE, (2) AUTHENTICITY, It was the real deal, filled with service information, including the specific information I required. (3) PRIVACY, I didn't start to get slammed with spam. (4) EASY TRANSACTION. Painless. (5) COMPLETE, I have found several manuals here, that I could find nowhere else. (6) I will be a repeat customer!
;
Well done!!! I found what I need to have, indeed!
Furthermore, due to my hobby is repairing vintage equipments, I added this web site in my desk toolbar because I have in mind to search further service manuals. Thanks a lot www.owner-manuals.com !
Regards, Maurizio
CD SECTION
Note: 1. CD Block basically constructed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. 3. Use the oscilloscope with more than 10 M� impedance. 4. Clean an objective lens by an applicator with neutral detergent when the signal level is low than specified value with the following checks. Focus Bias Adjustment Setting: This adjustment is performed with the set placed horizontally.
oscilloscope SERVO board TP (RF) TP (RF. GND)
+ �
Focus Gain Adjustment (Coarse adjustment) This adjustment is not required unless the following parts are replaced: � Optical pick-up � RV4 Procedure: 1. Set RV4 to the standard position. (mechanical center) 2. Check whether operation noise (while noise type) caused by the 2-axis device (lens section of the optical pick-up) is abnormally loud. If the operation noise is too loud, turn RV4 slightly counterclockwise. � If the gain is too low: Focus does not function and no music is selected. � If the gain is too high: Noise caused by scratches and dust is heard and the operation becomes unstable. Adjustment Location: servo board Adjustment Location: servo board (component side)
Procedure: 1. Connect an oscilloscope between TP (RF) and TP (RF. GND) on the SERVO board. 2. Connect the power supply. 3. Push the RESET button (S881) on the DISPLAY board. 4. Insert the disc (YEDS-18) and playback. 5. Adjust RV1 so that the oscilloscope waveform is clear and check RF signal level is correct or not. Note: Clear RF signal waveform means that the sharp ��� can be clearly distinguished at the center of the waveform.
RF signal waveform IC3 CN2
FOCUS GAIN ADJ RV4
VOLT/DIV: 200 mV TIME/DIV: 500 nS CN1
IC1 IC2
TP (RF. GND)
level: 1.0 � 1.5 Vp-p
� When observing the eye pattern, set the oscilloscope to AC range and raise the vertical sensitivity so that it may be easily seen. Adjustment Location: servo board
TP (RF) CN3
RV1 FOCUS BIAS ADJ
� 18 �
|
|
|
> |
|