|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
ADJUSTMENTS IMPORTANT NOTICE
Do not attempt to adjust the following service adjustments except when adjustments are required in servicing otherwise it may cause loss of performance and product safety. + B VOLTAGE ADJUSTMENT 1. Receive white raster pattern. 2. Set controls to normal. 3. Connect digital voltmetre to test point TP-B and GND. 4. Adjust voltage to 130 ±0.5V by using VR641.
DRIVE ADJUSTMENT 6. Select item no.3 �REGULAR 3, GRY� (G-Drive) or 4 �REGULAR 4, GRY� (B-Drive) and adjust both initially to 3F. 7. Change data value of each item by using LEVEL + or LEVEL - button to obtain the proper white balance. PCC ADJUSTMENT
AGC ADJUSTMENT 1. Connect digital voltmetre to test point TP-A and GND. 2. Using the CS button, input and tune an RF signal which is UHF to the clearest station. 4. Press the LEVEL+ or LEVEL - button to adjust voltage to be 3.2Vdc. 5. Enter to the service mode and select mode �REGULAR�, and select item no.1 �REGULAR 1, AGC�.
PCC ADJUSTMENT 1. Receive cross hatch pattern and set screen mode to �FULL�. 2. Enter to the service mode and select mode �WIDE�, and select item no. 7 �WIDE 7.P PCC�. 3. Press the LEVEL+ or LEVEL - button to adjust the vertical line to be straight.
FOCUS ADJUSTMENT By using FOCUS VR, adjust focus control for well defined scanning lines. TRAPEZOID ADJUSTMENT 1. Receive cross hatch pattern and set screen mode to �FULL�. 2. Enter to the service mode and select mode �WIDE�, and select item no. 8 �WIDE 8.P TRP�. 3. Press the LEVEL+ or LEVEL - button to correct the trapezum distortion of the vertical line.
GREY SCALE ADJUSTMENT SCREEN ADJUSTMENT 1. Receive black & white pattern. 2. Enter to the service mode and select mode �REGULAR�, and select item no. 2 �REGULAR 2, CUT�. The horizontal line will appear on the screen. 3. Using the numeric buttons shown set each colour to minimum by decreasing to the point where any further decrease resets the adjustment to maximum value. 4. Set the SCREEN VR for one colour to be just visible. BIAS ADJUSTMENT 5. By using the buttons 1, 2, 4, 5, 7, 8 on the remote control, adjust the line to be white. The key allocation is as follows;
Button No. Operation 1 Increase Red 2 Decrease Red 4 Increase Green 5 Decrease Green 7 Increase Blue 8 Decrease Blue
-10C2KTV
|
|
|
> |
|
