|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Owner-manuals.com is the best Possibility to give vantage HIGH CLASS Elektronic COMPONENTS
a new Life.Thanks alot for your perfekt Service.
;
I am proud of you. In the future, I benefited from your services.
;
I found this manual to be complete in every detail. Besides the schematic it has a complete set of alignment instructions which are easy to understand. It also includes a complete parts list as well as an explanation of how the power supply and safety shutdown circuits operate. Even a schematic of the tuner is included.
 ;
The product was good and just what I needed, however I had moderate difficulty with the down load because the sight would not recognize my pass word. I was finally given a direct link to the manual and that worked.
;
Very quick and easy website to use and fast download of manual, quality of manual is excellent and will be pleased to use this service again in the future, thanks so much!
SERVICE CONTROL ADJUSTMENT
B1 POWER SUPPLY ADJUSTMENT 1. Set VR641 to be mechanical centre before pressing the main switch. 2. Tune the receiver to PAL circular pattern. 3. Set brightness and contrast controls to normal. 4. Connect digital V-meter to test point "TP-B". 5. By using VR641, adjust voltage to 150 ± 0.5 V.
V-Outout SW501 +8V TP-E o-coupler SW1901 SW1902 SW1903 SW1904 Prog.+ Prog.Vol.+ Vol.VR361 Q641 IC651
H-Output
VR641
Q681 T101 +B ADJ.
5. Set mode to one horizontal scanning line, how to set refer to "service mode" 6. Set screen VR for one colour to be just visible. [BIAS VR ADJUSTMENT] 7. By using VR601, VR611 or VR621, adjust line to be white. 8. Set screen mode OFF, how to set refer to "service mode" [DRIVE VR ADJUSTMENT] 9. By using VR602 and VR612, adjust white balance. HIGH VOLTAGE & WIDTH ADJUSTMENT [HIGH VOLTAGE ADJUSTMENT] 1. Tune the receiver to circular pattern. 2. Set brightness and contrast controls to maximum. 3. Connect digital V-meter to both terminals of R224, and high voltage meter to CRT anode. 4. Confirm high voltage to be 26.0 ± 1 KV at beam current 1.3, and less than 29.0 KV at 0 beam current. [H-WIDTH ADJUSTMENT] 5. Adjust VR462 to obtain proper VR642
T611 Converter Trans Transformer
SIF Board
IC801 CPU A101 Tuner
F601 SW601
AFT ADJUSTMENT 1. Tune the receiver to the clearest station. 2. By using T141, adjust AFT to obtain the best picture.
611 V-Centre
T481
Main switch Fuse
T141
TPRC Transformer
H- width. 6. Reconfirm high voltage. H-CENTRE ADJUSTMENT 1. Tune the receiver to circular pattern. 2. Adjust H-centre by using VR361.
VR501 SW501 1H Delay Q-SOUND Board
Q432
IC652
Q501
H-Centre
VR131
Q-SOUND Board
V-CENTRE ADJUSTMENT R224 1. Tune the receiver to circular pattern. 2. Adjust V-centre by using SW501.
AV2 SW.
IC501 +12V
VR501 V-Size
IC271 1H Delay
Q432
IC281
IC1201
H-Width
Scart 2
Scart 1
IC1202 T141 AGC Int./Ext. SW. VR641
V-SIZE ADJUSTMENT 1. Tune the receiver to circular pattern. 2. Adjust V-size by using VR501.
IC1202 Q461
SIF Board
VR131
AGC ADJUSTMENT NOTE: Do not attempt this adjustment with weak signal. 1. Tune the receiver to the clearest station. 2. Set AGC VR(VR131) in direction which causes snow noise to appear, then in the opposite direction until snow noise just disappears.
FOCUS ADJUSTMENT By using FOCUS VR, adjust focus control for good scanning lines.
IC201 IF/Video/Croma/Def. Q501 VR361 VR462 H-Centre
IC501 V-Outout
V-Size
IC271
H-Output
V-Centre
GREY SCALE ADJUSTMENT [SCREEN VR ADJUSTMENT] 1. Tune the receiver to the white pattern. 2. Set brightness and contrast controls to normal. 3. Set VR602and VR612 to be mechanical centre. 4. Turn VR601, VR611 and VR621 fully counterclockwise.
TP-E
IC281
VR131
Scart 2
Scart 1
SW501 -7-
VR501
AGC Int./Ext. SW.
IC1201 AV2 SW.
VR361
A101 Tuner Flyback TP-B
T451
F7VVV
J213
IC201 IF/Video/Croma/Def.
Q462 T101
|
|
|
> |
|
