|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Quick site processing. A complete and very useful manual with all details. Thank you!
;
Quick service response. A useful and very rare service manual with all details. I recomend this service.
;
I ordered this manual sometime in the afternoon and I received it on my e-mail the same evening.
This is a fantastically good and properly scanned copy of the original manual. All pages are of the same scale and they overlap each other. It means that you can print the manual and easily make it as a convenient paper manual.
The content of the manual is fantastic. Alignment descriptions, PCB layouts and elementary diagrams are explicit and precise. I immediately found what I was looking for. Thanks to this manual and Owner-Manuals.com my amplifier is alive again. Many thanx indded!
;
The manual was well-scanned and easy to read. As an added bonus, the Operator's Manual was bundled with the Service Manual!
I'd definitely use owner-manuals.com again.
;
Finally, i found one website, where i can download this service manual , and fix my hifi. The service manual is very good, and easy to download and to print.
ADJUSTMENTS IMPORTANT NOTICE
Do not attempt to adjust the following service adjustments except when adjustments are required in servicing otherwise it may cause loss of performance and product safety. + B VOLTAGE ADJUSTMENT 1. Receive white raster pattern. 2. Set controls to normal. 3. Connect digital voltmetre to test point TP-B and GND. 4. Adjust voltage to 150 ±0.5V by using VR641. DRIVE ADJUSTMENT 6. Select item no.3 �REGULAR 3, GRY� (G-Drive) or 4 �REGULAR 4, GRY� (B-Drive) and adjust both initially to 3F. 7. Change data value of each item by using LEVEL + or LEVEL - button to obtain the proper white balance. PCC ADJUSTMENT AGC ADJUSTMENT 1. Input and tune an RF signal which is UHF to the clearest station. 2. Connect digital voltmetre to test point TP-A and GND. 4. Enter to the service mode and select mode �REGULAR�, and select item no.1 �REGULAR 1, AGC�. 5. Press the LEVEL+ or LEVEL - button to adjust voltage to be 3.2Vdc. PCC ADJUSTMENT 1. Receive cross hatch pattern and set screen mode to �FULL�. 2. Enter to the service mode and select mode �WIDE�, and select item no. 7 �WIDE 7.P PCC�. 3. Press the LEVEL+ or LEVEL - button to adjust the vertical line to be straight.
FOCUS ADJUSTMENT By using FOCUS VR, adjust focus control for well defined scanning lines. TRAPEZOID ADJUSTMENT 1. Receive cross hatch pattern and set screen mode to �FULL�. 2. Enter to the service mode and select mode �WIDE�, and select item no. 8 �WIDE 8.P TRP�. 3. Press the LEVEL+ or LEVEL - button to correct the trapezum distortion of the vertical line.
GREY SCALE ADJUSTMENT SCREEN ADJUSTMENT 1. Receive black & white pattern. 2. Enter to the service mode and select mode �REGULAR�, and select item no. 2 �REGULAR 2, CUT�. The horizontal line will appear on the screen. 3. Set the SCREEN VR for one colour to be just visible. 4. Using the numeric buttons shown set each colour to minimum by decreasing to the point where any further decrease resets the adjustment to maximum value. BIAS ADJUSTMENT 5. By using the buttons 1, 2, 4, 5, 7, 8 on the remote control, adjust the line to be white. The key allocation is as follows;
Button No. Operation 1 Increase Red 2 Decrease Red 4 Increase Green 5 Decrease Green 7 Increase Blue 8 Decrease Blue
-10C2WZV
|
|
|
> |
|
