|
|
|
Who's Online
There currently are 5907 guests online. |
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
;
Very comprehensive document which is a must-have for any Satellit 2100 owner whose set up is somewhat intricate. Due to the bad quality of the pictures that are rather dark and a bit blurred I gave 4-star feedback.
;
The manual was missing 2 pages but when I presented the problem to the company they made every attempt to get the 2 pages to me, when they couldn't they refunded my money. A very pleasing and easy transaction. The manual they provided was the original, it was concise and to the point. I plan to do business with this company again when should the need arise.
;
The owners manual is very good. all my how to questions were answered in detail.
2. Insert cord brackets into slotted holes in rear panel and secure with screws provided.
Connect Vent
1. Using a 4" (10.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Make sure the vent is secured to exhaust hood with a 4" (10.2 cm) clamp. 2. Move dryer into final position. Do not crush or kink vent. Make sure dryer is level. 3. (On gas models) Check to be sure there are no kinks in the flexible gas line.
A
Complete Installation
B C
A. Cord bracket B. Slotted hole C. Screw
1. Check to be sure all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped. 2. Check to be sure you have all of your tools. 3. Dispose of/recycle all packaging materials. 4. Check the dryer�s final location. Be sure the vent is not crushed or kinked. 5. Check to be sure the dryer is on a level surface. 6. Plug into a grounded 3 prong outlet. Turn power on. 7. Remove the blue protective film on the console and any tape remaining on the dryer. Remove tape from the lint screen (located on inside back wall of dryer). 8. Read �Dryer Use.� 9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust. 10. To test the dryer, set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following:
s s s
NOTE: Power supply cord may be wrapped around the brackets for storage convenience when dryer is not in use.
Install casters
1. Lay the dryer on its side. 2. Use the carton to prevent damage to the dryer.
Controls are set in a running or �On� position. Start button has been firmly pushed. Dryer is plugged into a grounded 3 prong outlet. Electrical supply is connected. House fuse is intact and tight, or circuit breaker has not tripped.
3. Screw casters into dryer base at four corners and tighten securely. 4. Set the dryer upright. In doing so, be careful that the dryer does not roll away from you. 5. NOTE: Permanent installations require 4 dryer feet. See �Assistance or Service� section for ordering information.
s s s
Dryer door is closed. 11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you do not feel heat, check the following:
s
Controls are set on a heated cycle, not an air cycle.
NOTE: You may notice a burning odor when dryer is first heated. This odor is common when the heating element is first used. The odor will go away.
9
|
|
|
> |
|
