|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
;
It is OK, this manual help me to repair my dynacord
 ;
Good manual. Even it is an old printed manual, it is well scanned and complete, with all drawings, schematics and parts list. Very good return for the cost.
SECTION 5 MECHANICAL ADJUSTMENTS
Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement
Mode FWD FWD back tension REV REV back tension FF/REW Torque meter CQ-102C Meter reading 3.04 � 6.96 N � m (31 to 71 g � cm) (0.43 � 0.98 oz � inch) 0.20 � 0.58 N � m (2 to 6 g � cm) (0.02 � 0.08 oz � inch) 3.04 � 6.96 N � m (31 to 71 g � cm) (0.43 � 0.98 oz � inch) 0.20 � 0.58 N � m (2 to 6 g � cm) (0.02 � 0.08 oz � inch) 6.97 � 14.02 N � m (71 to 143 g � cm) (0.98 � 1.99 oz � inch) 0.98 N � m or more (100 g or more) (3.53 oz or more) 0.98 N � m or more (100 g or more) (3.53 oz or more)
HCD-CL1/CL3 SECTION 6 ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB=0.775V
1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjusted. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and R-CH. 7. Switches and controls should be set as follows unless otherwise specified.
Tape P-4-A100 WS-48B Signal 10 kHz, �10 dB 3 kHz, 0 dB Used for Azimuth Adjustment Tape Speed Adjustment
CQ-102C
Record/Playback Head Azimuth Adjustment Procedure: 1. Mode : Playback
test tape P-4-A100 (10kHz, �10dB) main board CN301 Pin 1 (L-ch) Pin 3 (R-ch) set
CQ-102RC
CQ-102RC
CQ-201B
level meter
FWD tension REV tension
CQ-403A CQ-403R
+ �
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1 dB of peak.
L-CH peak
output level
within 1 dB within 1dB
screw position
R-CH peak screw position
L-CH peak
R-CH peak
17
 $4.99 CHC-CL1 SONY
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
