|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the manual I got for my amateur (ham) radio. Without it I could not figure out how to input and/or change the P/L setting on my radio. It drove me nuts as the radio was essentially useless. That all changed when my manual came. Then it took only minutes and I was done. Now my radio works fine. This is an exceptionally good resource as it's a very easy and user friendly download. Thank you very much! Dziękujemy za!
 ;
It answered my question, which was how to load the paper. I did notice that the very end of the manual was not visible.
;
The product manual I received was exactly what I was looking for, delivered painlessly at a very fair price. I can't ask for any more than that.
;
Very well done!!!!! congratulations. It was a bit longer than usual the wiating time even if it was on time (in 24 hours).
;
Last week I bought a second hand BAUKNECHT TRK4850 DRYER. It is a professional machine with many programs and switch options. I feared it would be a huge quest to find a manual. I was delighted when I found owner-manuals.com. After payment I received the file to download the next day already. The quality is great. I am very happy. Thanks!
but kindly the distributions of the operating programs not find in the owners manual,can you help me to understand the operating programs instructions thank you
Follow this Natronal Sanrtatron Foundatron dure to assure that the machine IS clean
approved
proce-
1. Both Cleanrng pare as follows Cleaning Solulion-
and Sanrtizing
solutions
are requrred
Pre-
5. Set the servrce swatch to the �Clean� posrtron and preheat the water system by pourrng hot water Into the reservorr pan until the lower pump housrng IS covered. Circulate the hot water for 5 minutes then set switch to Off�. to siphon water out of the reservoir pan Reset switch to Clean See Fig 6
Powdered citric acid is available from many drug stores or supply houses. MIX 113 cup of crystals to one quart of hot water. Ice machines with one (I) or two (2) freezing plates require 4 quarts of cleaner. Ice machines with 3 freezing plates require 5% yual-ts of cleaner. Commercial Ice machine cleaners are also available In liquid form and should be mIxed accordrng to instructions on the label These ice machine cleaners are avarlable through commercral refrigeration supply houses
WARNING: Most Ice machine cleaners are crtrrc or phosphorrc acid which can irritate even after drlutron In case of contact with eyes. flush eyes thoroughly with fresh water and contact a physician rmmedrately In case of contact wrth skrn rtnse well with water If swallowed. give large amounts of water and contact a physican lmmedrately Do not Induce vomrttrng KEEP OUT OF REACH OF CHILDREN
FIG. 6
6. Slowly pour the hot mixed cleanrng solutron Into the reservoir pan. If the solutron foams stop pourrng untrl the foaming subsides and then contrnue pouring until the lower pump housing IS covered to circulate until the scale on the freezsystem parts has drssolved
Sanitizing
Solution-
Common laundry bleach mIxed at a ratro of � 1 oz to a gallon of water WIII make a samtiring solution of 100 ppm 2. If the machine IS operating A. Shut off the water sc~pply to the machine B. Remove the front panel of the ice maker
7. Allow the solution ing plates and water
and gently
raise up the arm of the ice thickness control C. Remove the Ice sheets from the freezing plate D. Place the service switch In the Off postron
8. When the plates are clean. place the service switch In the OFF postron This allows the cleaning solutron to srphon out of the reservoir pan tnto the drain
3. If the machrne IS not operating A. Place the servrce switch in the Clean posrtron allow the water reservoir pan to ref!lI B. Shut off the water supply to the machrne C. Place the servrce swatch In the Off posItIon
and
NOTE: As a genera/ ruie c/rcu/at/ng the cieaning so/ut/on 20 to 30 minutes will remove a// scaie format/on Severe s&e formation may requjre repeating the cieanlng cycie with fresh soiut~on
4. Remove all Ice from the storage brn and cutter grid If Ice IS difficult to remove from the grid wait untrl grid IS removed from the machrne and then melt the Ice off with water Pullrng the Ice slab off the grad may stretch or break grid wires which would cause the machine to malfunctron
|
|
|
> |
|
