|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It is perfect, exactly what we needed. It's like the paper version but less clutter.
 ;
Received my manual within 24 hours. Very clear scan of the manual I needed. Thanks!
;
Very clear scan, I recommend it. Definitely a must have for any 3362 owner.
Alpine could have written a slightly more complete manual, though. It's already pretty huge, but the unit has so many functions, I feel some more explanation would have been better.
Yamaha's manual of their comparable YDSP-1 is a little better in my opinion.
;
Immediate response with excellent service - highly reccommended
;
Correct manual received and of good quality but the contents of the file for the Service Manual for the same monitor is for a 20" TV not the RGB Monitor.
Surface Cooking
IGNITION SYSTEM
Your range will feature pilotless ignition; a spark from the ignitor lights the burner. The igniter is located at the back side of each surface burner,
TO LIGHT SEALED BURNER
1. Place utensil on burner grate. 2. Push in and turn knob to the UTE position. After the burner lights, turn the knob to the desired flame size.
ADDITIONAL INFORMATION
� When the range is first installed, the pilots may be difficult to light due to air in the gasline. To bleed offair from the line, hold a lighted match next to the burner and turn knob on. When the burner
Ignitor. REARVIEWOFSEALEDBURNER To operate surface burner during a power failure: _ 1. Holda lightedmatchtothe desired surfaceburnerhead. 2. Turn knobtothe UTE position. he T burnerwillthen light, 3. Adjustthe flameto the desiredlevel. CAUTION: When lighting surface the burner,be sureall of the controls are in the OFF position.Strikethe match firstand holditin position beforeturning the knobto the LITE position,
� Be sure all surface controls are set in the OFF position prior to supplying gas to the appliance. All four ignitors will spark when any surfaceburner knob is turned to the LITE position. � CAUTION: If flameoff and proceed as directed. lights,turn the knob shouldgo out during a cookingoperation,turnthe burner off. If gas has accumulated and a strong gas odor is detected, wait 5 minutes for the gas to dissipate before relighting burner. � You mayheara "popping" soundonLP gas when the sudace burneris turned off.This is a normaloperatingsound of the burner. � If a knobis turnedveryquicklyfromHI to LO setting,the flamemay goout,particularlyifthe burneris cold.
NOTE: The knob on your appliance may not look like the knob in this illustration, but it will operate as describedin this manual, A sparking sound will be heard and the burnerwilllight.When oneburner isturnedon,allfour ignitorswill spark, The sparking will not stop until the knobis turnedfromthe LITE position.
ABOUT THE SURFACE BURNER FLAME
�
BURNERS* (if equipped) SUPER SPEED SEALED SUPER SPEED sealedburners. Refer S°me m°dels feature °ne °r tw° special range is equipped with this feature. See inside front cover for location of rating plate. to the rating plate to determine if your
A properly adjusted burner with clean
___
__
t_
_
� On naturalgas, the few sec°nds" POr_S light within aflame willbe blue will no trace of yellow in the flame. A yellow flame indicates an improper with a deeper bluecore; wastes fuel, so mixture of air/gas. This there shouldbe have a serviceman adjust the mixture if
Location of burners:-
_JP"IP'-_ "_ Ifthis occurs, turn the knob to the OFF
l_l
L
SUPER SPEED BURNER
j
occurS.isCeptable., a OnnotLPnecessary.gas,ThisSOmeis yellow flame normalYell°WandtippingadjustmentiS severalagain, ac- lightP°siti°n'the burnerWait seconds, then
Use the SUPER SPEED burner to quickly bring water to a boil or when using large cookware.
(continued next page)
�U.S.PatentPending
5
|
|
|
> |
|
