|
Who's Online
There currently are 5410 guests online.
|
Categories
|
Information
|
Featured Product
|
|
|
|
|
There are currently no product reviews.
;
Thank´s for your help, I already recived these manual from you
;
Thank you for your manual It has the basic things to and i use the Oszi for Longer Time.
THX
;
Actually, I was looking for this information for 3 years!...now thanks to you, the manual is on my hands and of great help, cause I understand now where I was doing wrong connections and wires...excellent, I'll be back to you if in need, thank you.
;
This manual covers the main equipment features only. While it also includes the procedure for saving and loading from the now long obsolete memory cards it does not mention the how to operate with the optional floppy drive interface so I am still at a loss about how to use this! Note that there is a separate manual covering the MIDI interface and programming via the keyboard, not included in this download. You will also need to get hold of this if you want to use the MIDI interface properly. Basically there is little difference between this manual and the free to download manual for the similar PR60 model.
;
Good list of manuals. I found a very rare one and easily get. Should be promptly to download, as we must to wait hours even after confirmed payment.
10815 87801 A3 12pp Brdsht
10/6/03
10:39 AM
Page 1
INSTALLATION
Connecting the Drain Kit
1. Unscrew the plastic nut J from the connector at the top, rear of the machine. Keep the rubber washer K. 3. Push the free end of the hose through the threaded end of the nut and pull through so that the flange of the plastic elbow, at the other end of the hose is seated against the inside of the nut. 4. Insert the rubber washer K. 5. Screw the nut onto the connector on the back of the machine and position the elbow ensuring the nut is tight.
K J
Your dryer does not need to be installed adjacent to a drain.
It can be positioned up to 4m from the drain using the kit provided (this can be extended using additional hose if required). The small bore flexible outlet pipe can easily run behind existing units or along a skirting board. If in doubt, consult an experienced plumber.
Figure 1
50cm
The outlet drain hose may be routed through a wall, window or door frame. (The water can be re used if collected) see figures 1 and 2.
Caution: When discharging during cold periods ensure that the hose is protected from freezing in areas where the temperature will drop below 4�C. The hose must NOT be submerged in the discharged water a gap of at least 10cm must be left between the hose end and the surface of the water. 1. A 12mm hole can be drilled through the wall, window or door frame, not more than 1.5m from the dryer base. Check for pipes and wires before commencing drilling. 2. Feed outlet hose through the hole. 3. Fix outlet hose to the wall or skirting board with the clips supplied at 50cm intervals. When fixing outlet hose around corners, ensure a minimum radius of 10cm and fit two clips as shown in Figure 3. 4. Cut outlet hose to the length required. 5. Check that the pipe is not kinked.
Figure 2
1.5m 105 max.
Figure 4
Figure 3
Drain your dryer into a sink or bucket, Figure 4.
see
1. Fix outlet hose to the wall or skirting board if required with the clips supplied at 50cm intervals. When fixing outlet hose around corners, ensure a minimum radius of 10cm and fit two clips as shown in Figure 3. 2. Cut outlet hose to the length required.
Connect your dryer to an unused sink drain outlet, see Figure 5.
If a blanking cap or plug is provided: 1. Remove cap/plug (1) and fit connector (2a) (not supplied). 2. Connect elbow (not supplied) (3a) to connector (2a). 3. Cut dryer hose (4) to length and insert into hole in plug. 4. After the first run check the installation for leaks. 5. If water appears under your dryer, check that the outlet hose is not kinked, blocked or frozen.
2a 3a
Figure 5
|
|
|
> |
|