|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
a solid deal - quick and without any problems.
I life in europe - with downloads no loosing time
once again
 ;
got exactly what i ordered in a very timely manner. will use again for other manuals
;
I'm happy. Good quality. Very helped me with my work..............................
;
This is the second Manual I have ordered from owner-manuals, I give it five stars because it is exactly what I expected given the age of the equipment. So the contents look a bit aged and the pictures a bit grainy, it fulfills my needs and I am glad I can still get hold of them.
;
thank u so much for this manual that was so cheap that i thought it was a scam but i gambled anyway because it was too good of a deal to pass up and behold,the manual has everything and details of everything even the screws and im still amazed and very happy with my manual .so take my word and jump on it before they realize how cheap they selling thier manuals..thank you so much for taking time to read my thoughts
CP-A100 / ED-A100 / ED-A110 (A1DN)
Requesting projector status (Get command) (1) Send the following request code from the PC to the projector. Header + Command data (�02H� + �00H� + type (2 bytes) + �00H� + �00H�) (2) The projector returns the response code �1DH� + data (2 bytes) to the PC. Changing the projector settings (Set command) (1) Send the following setting code from the PC to the projector. Header + Command data (�01H� + �00H� + type (2 bytes) + setting code (2 bytes)) (2) The projector changes the setting based on the above setting code. (3) The projector returns the response code �06H� to the PC. Using the projector default settings (Reset Command) (1) The PC sends the following default setting code to the projector. Header + Command data (�06H� + �00H� + type (2 bytes) + �00H� + �00H�) (2) The projector changes the speci�ed setting to the default value. (3) The projector returns the response code �06H� to the PC. Increasing the projector setting value (Increment command) (1) The PC sends the following increment code to the projector. Header + Command data (�04H� + �00H� + type (2 bytes) + �00H� + �00H�) (2) The projector increases the setting value on the above setting code. (3) The projector returns the response code �06H� to the PC. Decreasing the projector setting value (Decrement command) (1) The PC sends the following decrement code to the projector. Header + Command data (�05H� + �00H� + type (2 bytes) + �00H� + �00H�) (2) The projector decreases the setting value on the above setting code. (3) The projector returns the response code �06H� to the PC. When the projector cannot understand the received command When the projector cannot understand the received command, the error code �15H� is sent back to the PC. Sometimes the projector cannot properly receive the command. In such a case, the command is not executed and the error code �15H� is sent back to the PC. If this error code is returned, send the same command again. When the projector cannot execute the received command. When the projector cannot execute the received command, the error code �1CH� + �xxxxH� is sent back to the PC. When the data length is greater than indicated by the data length code, the projector ignore the excess data code. Conversely when the data length is shorter than indicated by the data length code, an error code will be returned to the PC.
NOTE � Operation cannot be guaranteed when the projector receives an unde�ned command or data. � Provide an interval of at least 40ms between the response code and any other code. � The projector outputs test data when the power supply is switched ON, and when the lamp is lit. Ignore this data. � Commands are not accepted during warm-up.
74
|
|
|
> |
|
