|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Very good manual for Technics SL 303. Manuale molto utile.
;
About one hour after checkout, the manual was available for download. Clear reading and detailed. Thanks
;
Excellent transaction - clean document received - Thanks a lot
;
Manual is in German but complete. I needed this one to fix a long lasting problem with the internal PSU of the camera. Most of the capacitors begin to leak after a few years wich results in the inability to power on the camera. When you try to turn it on the power led flickers and the unit directly turns off. Thanks to this manual I was able to locate all bad cap's and to dis- and reassemble the camera without any problems.
 ;
We received the manual in a timely manner and it was exactly what we were expecting.
CP-SX5600W
4-4 CYCLE OFFSET adjustment (vertical stripe adjustment)
Signals for internal adjustment Adjustment procedure 1. Make this adjustment after completing the adjustment in 4-3 Flicker adjustment. 2. Use DAC-P - CYCLE - R: in the Adjustment menu
24 48 72 /256 /256 /256 96 120 /256 /256 144 168 /256 /256 192 /256
to adjust so that the vertical lines spaced every 12 dots are as inconspicuous as possible. 3. In the same way, use DAC-P - CYCLE - G: in the Adjustment menu to adjust vertical stripes of G color. 4. In the same way, use DAC-P - CYCLE - B: in the Adjustment menu to adjust vertical stripes of B color.
CYCLE
NO. 1
R
0
G
0
B
0
Major adjustment cycle No.
4-5 White balance adjustment
GAMMA MENU (left side)
VID-AD C.UNIF. 93% 86% 75% 43% 29% 14% 0% DAC-P R 0 0 0 0 0 0 0 GAMMA GAMMA G 0 0 0 0 0 0 0 B 0 0 0 0 0 0 0
Preparations 1. Perform these adjustments after the CYCLE OFFSET adjustment described in Section 4-4. 2. Reset gamma correction before adjustment. Place the cursor on [GAMMA] (left side) in the Adjustment menu, press the [RESET] key and select [DEFAULT]. Now press the [RESET] key again and press the [MAGNIFY-OFF] button of the Remote control transmitter for 5 seconds or more (the confirming to �MICRO� reset menu will appear).
GAMMA GAMMA G 128 128 B 128 128
GAMMA MENU (right side)
VID-AD C.UNIF. DAC-P R SUB CONTRAST SUB BRIGHT 128 128
Place the cursor on [GAMMA] (right side) in the Adjustment menu, press the [RESET] key and select [DEFAUT]. 3. Whisper mode set to [Normal] in the Setup menu.
Adjustment procedure 1. First, adjust the G color. 2. GAMMA mode set to [DYNAMIC] in the lmage menu. 3. BRIGHT and CONTRAST set to in the Setup menu. 4. Place the cursor on Slide Show in the Adjustment menu [A/D], press the [ ] key three times to display G monochrome and adjust the luminance at the center of the screen. Make a note of the setting (here assumed to be A [lx]). Press the MENU key to return. 6
5. BRIGHT and CONTRAST is returned to default in the Setup menu. 6 GAMMA mode is returned to default in the lmage menu. 7 Place the cursor on 0%, measure the illumination at the center of the screen. Make a note of the setting (here assumed to be B [lx]. 8. Adjust Gamma, 93%, and G: in the Adjust menu so that luminance (Y) at the center of the screen is adjusted as follows. Y = (A-B) x 0.680 +B ± 2% [lx]
|
|
|
> |
|
