|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly what was needed to assess the product - excellent value and great service
 ;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
There shall be no slack in the wire in this area. The excess wire shall be folded and tucked under (which will prevent the wire from getting tangled in the upper cover).
The installation of the flexible cable shall be subject to the drawing in the bottom right corner of this sheet.
EPBX
EPGX
Flexible cable (G panel)
CNRM SP.R/SP.L LSW2
ERM2
EFZ1
PWB DRIVE ECN3
CNRM
26
The ECN1/ECN2 wires shall be laid so that the excess wires shall be laid out as shown in the figure below. ECN1 ECN2 Terminal board PWB DRIVE PWB RGB
Particular care shall be taken not to bend the wires when laying out them.
PWB DRIVE
Screw Washer CNSG Particular care shall be taken to prevent the CNSG/CNDS2 from getting entangled in the upper cover when mounting the cover. The excess CNSG wire shall be tucked under the PWB DRIVE.
The CNSG shall be secured to the PWB DRIVE with a screw.
CNDS2
Upper cover
ECN1 ECN2 EDS2 CNSG
EDI2
EDI1
ESW1
The installation of the flexible cable shall be subject to the drawing in the bottom right corner of this sheet. It shall be securely fitted Flexible cable to PWB FAN G01. (R panel) ERM1
EDI3 EPRX SP.L SP.R
ESW2 CNSW PAS3
Wire clamp
PWB R/C
PWB KEYBOARD
Particular care shall be taken to prevent the wire stopper from being twisted on the board. Flexible cable (B panel) The ECN3 shall be connected to the EMD1 prior to securing the PWB DRIVE. In addition, the installation of the flexible cable shall be subject to the drawing in the bottom right corner of this sheet. PWB DRIVE
EMD1 LSW1
The wire clamp shall be secured with a wire stopper to prevent it from moving.
CNFZ
Fan cover
PWB TEMP
ECN3 ETEM
POWER UNIT (BALLAST)
PAS6
Push the slack in the ECN3 cable between the ballast and PWB DRIVE. POWER UNIT (BALLAST) EMD1
Purse lock 8
The connectors for the ballast and power fan shall be clamped to the fan cover with a purse lock.
The installation of the flexible cable shall be subject to the drawing shown below. (1) Insert the flexible flat cable securely into the connector base. (Particular attention shall be paid to the inserting direction as this connector 1 has contacts on its underside). (2) Move the hinge in the arrow Flexible flat cable direction to securely lock it.
2
Connector base
Wiring for PWB DRIVE Mounting
|
|
|
> |
|
