|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
 ;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
;
Awesome quality manual. You really saved my bacon with this one. Was looking for some specific information with regards to my "new" vintage VCR that didn't come with the owners manual. This site is truely a goldmine of available manuals. The quality of the scans are top notch.
Thank-you so much for this awesome manual. If you're looking for this Sony SL-HF400 owners manual, this is the one you NEED to buy. Definitely worth the money.
;
The manual was made available promptly. I is a clean scan of the original. I had no problem downloading it. The scan was well centered and cleanly formatted. It is as good a product as can be had without being the original document.
Note: ¡While the private mode is active, only
FRONT L FRONT R
SOURCE LEVEL
Setting the AV1/AV2 input level
Make this setting if it is not possible to adjust the volume through the connected device (on the output side).
36
and can be
adjusted.
AV1 LEVEL TEST TONE
ON OFF
(Test tone output) : enables the test tone. : disables the test tone. default:
OFF
(Setting for AV1)
LOW HIGH
: sets the level low/sound volume increases. : sets the level high/sound volume decreases.
default:
HIGH
AV2 LEVEL
LOW HIGH
(Setting for AV2)
¡When the test tone is set to on, test signal (a continuous tone) is output from each speaker for approximately 2 seconds. Adjust the output balance so that the tone appears to
have the same volume from each speaker. Adjusting the output balance: Adjust the volume of all of the other speakers to the volume level of the speaker from which the test signal appears to be the quietest.
: sets the level low/sound volume increases. : sets the level high/sound volume decreases.
TIME ALIGNMENT
(Delay time setting of each speaker) Adjusting the timing with which the audio from each speaker reaches the listener�s position (Center speaker delay time setCENTER ting)
] : down,
Note: ¡If the input level from AV1/AV2 is too high, the audio will not be output normally. ¡After setting the input level The volume can be adjusted by pressing [+] or [�] (VOL) on the remote control. default: HIGH
CROSS OVER
Cut off frequency
LPF CUT OFF
] : down,
(Sub-woofer Low Pass Filter)
[ : up
Setting range: 0 ms to 5 ms (1 ms steps) 1 ms = 0.001 seconds default: 0 ms
[ : up Setting range: 63 Hz to 200 Hz default: 125 Hz
SUR
] : down,
(Surround speaker delay time setting) [ : up
HPF CUT OFF
] : down,
(High Pass Filter)
[ : up Setting range: off, 63 Hz to 200 Hz default: off
Setting range: 0 ms to 15 ms (1 ms steps) 1 ms = 0.001 seconds default: 0 ms this adjustment while listening to sound. ¡Make ¡If the speaker setting is NONE for a speaker, that speaker cannot be selected. ¡When �PRO LOGIC� is displayed, 15 ms are automatically added to the delay time setting for the surround speakers.
Note: ¡This setting is not available if CS Auto is set to ON . ¡ HPF CUT OFF is enabled only on the front speakers (R/L) and rear speakers (L/R).
CQ-VD6505U
English
37
|
|
|
> |
|
