|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Thr Video Recorder i have is quiet Old and the Producer could Not help me. So i w as very glad to find an offer for the owners Manual for a very fair Price.a I obtained the original Manual very quick and I am happy to have it now.
 ;
The PDF copy was immediately available on download after the payment. However, I noticed that the document was in German, and Ihad to contact a German translator to get it translated it to English. The quality of document is legible can be used for my purpose.
;
The manual was complete and of great quality. Originally a tri-lingual file, I first received only one language. After a note to owners-manuals.com, I quickly received the remaining languages... Great service, definitely worth it.
;
Thank you for providing this manual and at low cost.
The Philips scope is of excellent quality, longevity and build and had a couple of faults
when it was passed to me. Having the CCT diagrams is a blessing.
I have fixed the problems and also modded the scope to my requirements.
I have built a 24v Li-Ion pack for portable use from old but good laptop batts.
it is working beautifully and I am well pleased. Keep up the good work Guys.
;
manual was very helpful in learning how to propery use my washer. I could not find this manual anywhere else.
Note: ¡While the private mode is active, only
FRONT L FRONT R
SOURCE LEVEL
Setting the AV1/AV2 input level
Make this setting if it is not possible to adjust the volume through the connected device (on the output side).
36
and can be
adjusted.
AV1 LEVEL TEST TONE
ON OFF
(Test tone output) : enables the test tone. : disables the test tone. default:
OFF
(Setting for AV1)
LOW HIGH
: sets the level low/sound volume increases. : sets the level high/sound volume decreases.
default:
HIGH
AV2 LEVEL
LOW HIGH
(Setting for AV2)
¡When the test tone is set to on, test signal (a continuous tone) is output from each speaker for approximately 2 seconds. Adjust the output balance so that the tone appears to
have the same volume from each speaker. Adjusting the output balance: Adjust the volume of all of the other speakers to the volume level of the speaker from which the test signal appears to be the quietest.
: sets the level low/sound volume increases. : sets the level high/sound volume decreases.
TIME ALIGNMENT
Adjusting the timing with which the audio from each speaker reaches the listener�s position (Center speaker delay time setCENTER ting)
] : down,
Note: ¡If the input level from AV1/AV2 is too high, the audio will not be output normally. ¡After setting the input level The volume can be adjusted by pressing [+] or [�] (VOL) on the remote control or turning rotary volume controller on the unit. default: HIGH
CROSS OVER
Cut off frequency
[ : up
Setting range: 0 ms to 5 ms (1 ms steps) 1 ms = 0.001 seconds default: 0 ms
LPF CUT OFF
] : down,
(Sub-woofer Low Pass Filter)
[ : up Setting range: 63 Hz to 200 Hz default: 125 Hz
SUR
] : down,
(Surround speaker delay time setting) [ : up
HPF CUT OFF
] : down,
(High Pass Filter)
Setting range: 0 ms to 15 ms (1 ms steps) 1 ms = 0.001 seconds default: 0 ms ¡Make this adjustment while listening to sound. ¡If the speaker setting is NONE for a speaker, that speaker cannot be selected. ¡When �PRO LOGIC� is displayed, 15 ms are automatically added to the delay time setting for the surround speakers.
[ : up Setting range: off, 63 Hz to 200 Hz default: off
Note: ¡This setting is not available if CS Auto is set to ON . ¡ HPF CUT OFF is enabled only on the front speakers (R/L) and rear speakers (L/R).
CQ-VD7005U
English
37
|
|
|
> |
|
