|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Perfect. Very good service and very good scanning quality. All sheets are very legible. Thank's
 ;
My first manual from Owner-Manuals.com but not the last! I am very satisfied with the easy ordering and promt delivery of a manual I did not find anywhere else.
 ;
This manual is very helpfull to use the Power Supply. All technical information has been available.
For service use the circuit diagrams are very good.
Thanks .
 ;
Very comprehensive document which is a must-have for any Satellit 2100 owner whose set up is somewhat intricate. Due to the bad quality of the pictures that are rather dark and a bit blurred I gave 4-star feedback.
 ;
The manual was missing 2 pages but when I presented the problem to the company they made every attempt to get the 2 pages to me, when they couldn't they refunded my money. A very pleasing and easy transaction. The manual they provided was the original, it was concise and to the point. I plan to do business with this company again when should the need arise.
SCHEMATIC
DESCRIPTION RIGHT PANEL The right hand side of the CS1000 contains the cable scanning SEND jacks. If you are connecting a cable with an unmatched amount of pins or electronic connections, plug the end with the MAXIMUM connections to this side. The XLR jacks on this side are also used for the Phantom Power VOLTAGE test. This side contains the following jacks: 1/4�, Speak-on®, RCA, XLR Female, 1/8�, XLR Male, 7- Pin MIDI, RJ11, and RJ45.
LEFT PANEL The left hand side of the CS1000 contains the cable scanning RECEIVE jacks in Cable Test Mode. In Test Tone mode, these jacks are the 1 kHz test tone OUTPUT jacks. The XLR jacks on this side are also used for the Phantom Power Present test. The left panel contains the following jacks: Banana, 1/4� TRS, Speak-on®, RCA, XLR Female, 1/8� (3.5mm) TRS, XLR Male, 7-pin MIDI, RJ11, and RJ45.
TOP PANEL Battery 9 V: This is the cover for the 9 volt battery compartment. Test Tone / Cable Test Switch: Selects the operating mode of the CS1000 - Cable Test, Test Tone, Phantom Power test, or OFF.
1 2+ 1
BATTERY 9 V
32+ TEST TONE CABLE TEST pwr 3 2 1 1 2 -10 0 -20 +3 -30
dB
OFF
1 2+ 34+
TONE OUTPUT SIDE
2+
1 = ground + = positive polarity - = negative polarity
3 4 2 1 3 1 2 2 1 3 1 2 3 4 5 6 7
1 2 3 4 5 6 1 2 3 4 5 6 7 8
31 2+
1
+7
TONE LEVEL
32+
(NOTE: Levels indicated are BALANCED. For unbalanced levels, subtract 6 dB. )
pwr LED: Indicates the CS1000 is in either Cable Test or Test Tone mode. When this LED dims, battery replacement will be necessary. Tone Level: Adjusts the level of the 1 kHz test tone. The levels indicated by the knob are BALANCED levels. This means the device being tested is receiving both positive and negative polarity signals. If you are testing an unbalanced device, with only the positive signal and ground, divide the amount shown in half. Signal LEDs: These 16 LEDs (8 on the Send side, 8 Receive) indicate several things: � In Cable Test mode the lit LED on the SEND side indicates a signal being sent on corresponding pin number, on the RECEIVE side the lit LED indicates which pin that signal is being received on. � When testing Phantom Power Voltage, the bottom five LEDs on the SEND side will indicate the Phantom Power voltage. � When testing Phantom Power Presence, LEDs number two and three on the RECEIVE side will light if voltage is present on both pins.
3 2 1 3-
2+ 1
MADE IN USA
RECEIVE LINE
PHANTOM POWER PRESENT SEND LINE
1
1 2+ 34+ 5 6 7
1 2+ 34+ 5 6 1 2+ 34+ 5 6 7 8
1 2 3 4 5 6 8 7
1 2 3 4 5 6 8 7
>52 >42 >32 >11 >21
PHANTOM POWER VOLTAGE
5
2
|
|
 |
> |
|