|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
PRACTICAL SERVICE FIGURE
< TUNER SECTION >
1. FM VT Adjustment Settings : � Test point : TP2(VT) � Adjustment location : L006 Method : Set to FM 108.0MHz and adjust L006 so that the test point voltage becomes 6.0V ± 0.05V. 2. MW VT Adjustment Settings : � Test point : TP2(VT) � Adjustment location : L004 Method : Set to MW 1000kHz (U), and adjust L004 so that the test point voltage becomes 3.75V ± 0.05V. 3. FM Tracking Adjustment L005.........................................................................98.0MHz 4. MW Tracking Adjustment L003...........................................................................600kHz TC001.......................................................................1400kHz 5. AM IF Adjustment Settings : � Test point : TP1(DET) � Adjustment location : L007 Method : Adjust L007 so that the output level at 1400kHz becomes maximum.
< TUNER SECTION >
< FM SECTION >
Sensitivity: (THD 3%) Signal to Noise Ratio: (Input 60dB) Distortion: (Input 60dB) Intermediate frequency: Stereo separation: Less than 1.5% (at 98.0MHz) 10.7MHz ±0.1MHz More than 22dB Less than 19dB (88.0MHz) Less than 18dB (98.0MHz) Less than 18dB (108.0MHz) More than 60dB (at 98.0MHz)
< AM SECTION >
Sensitivity: (S/N 10dB) Distortion: (Input 74dB) Intermediate frequency: Less than 45dB (at 600kHz) Less than 45dB (at 1000kHz) Less than 45dB (at 1400kHz) Less than 1.5% 455kHz±3.5kHz
< CASSETTE SECTION >
Tape speed: Wow & flutter: S/N ratio: Distortion: Noise (PB): 3000Hz+3%-2% Less than 0.35% (JIS RMS) More than 35dB Less than 3.0% (PB) Less than 1mV (DC, MIN) Less than 1.2mV (AC, MIN) More than 45dB
< DECK SECTION >
6. Tape Speed Adjustment Settings : � Test tape : TTA�100 � Test point : J251 (PHONES jack) � Adjustment location : SFR of deck motor Method : Play back the test tape and adjust SFR so that the frequency counter reads 3000Hz ± 30Hz.
Erasing Ratio (W/O FILTER):
7. Head Azimuth Adjustment Settings : � Test tape : TTA�320 � Test point : J251 (PHONES jack) � Adjustment location : Azimuth adjustment screw Method : Play back the 8kHz signal of the test tape and adjust screw so that the output becomes maximum. 8. Bias frequncy Adjustment L801..................................................................85kHz±0.5kHz
< CD SECTION >
9. FE Balance Adjustment Settings : � Test point : IC401 PIN58 (VR), IC401 PIN 20 (FE) � Adjustment location : SFR430 Method : Playback the disc and adjust SFR430 so that the test point voltage becomes 0V.
25
 $4.99 CSDA170 AIWA
Owner's Manual Complete owner's manual in digital format. The manual will be available for download as PDF file aft…
|
|
|
> |
|
