|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
;
The service was great and the document was also great. Highly recommend!!!!
If anyone has a users manual... Please email me. need one. $ [email protected]
;
I needed a service manual as the display on my oscilloscope was very dim. I thought I'd give owner-manuals.com a try, as they advertised a huge number of manuals. Sure enough they had one listed. I bought it hoping it would be useful... actually, I bought it hoping it would be readable! I've had manuals from online sources in the past, and been very disappointed. Not this time! An excellent manual, complete, and very readable. Using it I fixed my 'scope, and as such the manual was an investment that paid off manyfold. Do I have any complaints? One very minor one - The circuit diagrams could have been scanned at a higher resolution, as some of the details were a little difficult to make out - not impossible, just not as easy as my old eyes would like! Overall, I'm very satisfied with my manual, and I will certainly be using this company again. Well done.
 ;
I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, pages are very clear to read, some of the pages are a bit tilted but overall it is great to have this manual available for purchase. Thanks
;
This is quiet a rare manual, I Have looked for this manual for quiet a while now, I have finally found it here. I believe this is the only place they have them in a very nice scan, Excellent guide: very clear, enabling us to print readable diagram overall it is great to have this manual available for purchase. This is a complete service manual no pages are missing. Thanks
Pin No. 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64
Pin Name LVSS RVSS RCHO RVDD MUTER XVDD XOUT XIN XVSS SBSY EFLG PW SFSY SBCK FSX WRQ RWC SQOUT COIN CQCK RES T11 16M 4.2M T5 CS T1
I/O � O O O
Description Left channel one-bit D/A converter ground. Must be connected to 0V. Right channel one-bit D/A converter ground. (Must be connected to 0V.) Right channel onr-bit D/A converter output. Right channel one-bit D/A converter power supply. Right channel one-bit D/A converter mute output. (Not used) Crystal oscillator power supply. Connections for a 16.9344 MHz crystal oscillator element.
I O O O O in standby state. (Not used) I O O I O I I readout clock input pin. This is Schmitt input. I O O O I I (Must be connected to 0V if not controlled.) I Test input. No pull-down resistor. (Must be connected to 0V.) Reset input. This pin must be set low briefly after power is first applied. Test output. Leave open. (Normally output a low level). (Not used) 16.9344 MHz output. (Not used) 4.2336 MHz output. Test input. A pull-down resistor is built-in. (Must be connected to 0V.) Chip seledt input. A pull-down resistor is built-in. Subcode readout clock input. This is a Schmitt input. Output pin for the 7.35 kHZ synchronization signal divided from the crystal oscillator. (Not used) Subcode Q output standby output. Read/write control input. This is a Schmitt input. Subcode Q output. Command input pin from control microprocessor. Input for both the command input acquisition clock and the SQOUT pin subcode Crystal oscillator ground. (Must be connected to 0V.) Subcode clock synchronization signal output. (Not used) C1, C2, sigle an double error correction monitor. (Not used) Subcode P, Q, R, S, T, U and W output. (Not used) Subcode frame synchronization signal output. This signal falls when the subcode are
�24�
|
|
|
> |
|
