|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent just what I needed to replace the electrolytic caps and make this old gem a beauty again. Was as scan of the original photocopied service manual.
;
It was helpful to get schematic with waveforms in important points and lot of service information. Manual is good quality, fast delivered. Of course it is hardcopy of paper one with all its disadvantages.
 ;
I want to give you a real heads-up for your desire to enable such people as I to acquire the information I need to maintain the older types of equipment such as this Akai HXA351W. You do a swell job with all the processes you have to perform so I can have a legible, thus usable
document which does not send me crazy trying to figure out the blurry text of a bad copy.
Very well done, Thomas.
;
This manual is very well presented and after printing out looks about as close to an original as I think you can get. The quality is second to none.
The content of the manual is comprehensive and I think it would be well suited to an audio repair professional which I'm not but I did find it very informative and helpful.
The cost of the manual is more than covered by the money I'll save when I change the keep memory battery now I have the relavant info.
Very pleased with my purchase and can recommend it wholeheartedly as I can other manuals I've downloaded from this site.
Regards
Limey Alex
;
Complete manual including mechanical part in good pdf quality. Shaded greys of the pcb due to pdf not perfect but usable.
1-30 CSPK-5000E
Configuring the System
Setting the synchronization mode
The CSP-5000E System Controller supports both line lock and VD-S. If a Sony VD-S lock camera is installed, you can turn on the VD setting to enable external syncronization.
4 5
Use the cursor keys to cycle through the options: OFF, and ON. Select �ON� for a Sony VD-S lock camera. Repeat the same procedure with other cameras. When you are ready, press the SET key to accept the changes.
Limiting the pan/tilt unit movement
Depending on the receiver used, you can use the �P/T LIMIT� setting to limit the pan/tilt unit movement in horizontal and vertical directions. This is available only when the receiver type of the camera is �TWIST PAIR.�
3
Select a receiver number. If necessary, press the NEXT or PREVIOUS key to see other pages. Then press the SET key.
P/T LIMIT � LEFT RIGHT UP DOWN CLEAR
1
From the main menu, select �INPUT CONFIGURE� and then press the SET key.
INPUT CONFIGURE � SOURCE ID CABLE COMPENSATION RECEIVER TYPE VD P/T LIMIT
1
From the main menu, select �INPUT COFIGURE� and then press the SET key.
INPUT CONFIGURE � SOURCE ID CABLE COMPENSATION RECEIVER TYPE VD P/T LIMIT
4
Use the cursor keys to select the direction you want to limit (RIGHT LIMIT in this example) and then press the SET key.
2
Select �VD� and then press the SET key.
VD � CAM 1 2 3 4 5 6 7 8 TYPE OFF OFF OFF OFF OFF OFF OFF OFF
2
Select �P/T LIMIT� and then press the SET key.
P/T LIMIT SELECT RECEIVER NO. �1 9 17 2 10 18 3 11 19 4 12 20 5 13 21 6 14 22 7 15 23 8 16 24 25 26 27 28 29 30 31 32
RIGHT LIMIT SETTING
5 6 7
Use the joyball to control the pan/tilt unit so that the camera moves to the rightmost position where you want to limit the movement. Press the SET key. Repeat the above procedure to limit the movement in other directions.
3
Select a camera number. If necessary, press the NEXT or PREVIOUS key to see other pages.
Note that only the receiver numbers whose �RECEIVER TYPE� is set to �TWIST PAIR� in the RECEIVER TYPE menu.
To clear the limit in all directions Select �CLEAR� in step 4 and then press the SET key.
32(EN)
33(EN)
|
|
|
> |
|
