|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good,readable manual. I found other manuals that were not readable when it came to part ID, but the one downloaded from owner-manual.com was better than expected. I will do buisness with owner-manual.com again.
;
Service Manual that I received was very helpful to me. Thank you.
;
The manual is well organized and is easy to read. The chapters are following normal way to proceed.
;
This scanned manual is well done in that most all the pages except for one is straight and clear- the way I would do them. One page was upside down but that happens. For the money that is charged on this site you get a pretty good deal. Now with complex repairs, I still prefer to us paper manuals which I have to buy at stereomanuals but the one I got here was much less than the $45 he was charging but this is a larger than normal manual for three different units. I am a picky manual user because I have used original manuals from Sony and Teac.
;
Very useful service manual, was exactly what i needed.Good quality,reasonable price.Thank you.
C-T2021
ELECTRICAL ADJUSTMENTS
2-11: OSD HORIZONTAL 1. Using the remote control, set brightness and contrast to normal position. 2. Activate the adjustment mode display of Fig. 1-1 and press the channel button (5) on the remote control to select "OTHERS". The Fig. 2-1 appears on the display. 3. Press the channel button (4) on the remote control to select "OSD H". 4. Press the VOL. UP/DOWN on the remote control until the difference of A and B becomes minimum. (Refer to Fig. 2-4) 2-13: SUB TINT/SUB COLOR 1. Receive the color bar pattern of NTSC. (RF Input) 2. Connect the oscilloscope to TP803. 3. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-5 appears on the display. 4. Press the channel button (4) on the remote control to select "TINT". 5. Press the VOL. UP/DOWN button on the remote control until the waveform becomes as shown in Fig. 2-6. 6. Connect the oscilloscope to TP801. 7. Press the CH DOWN button 1 time to set to "COLOR" mode. 8. Press the VOL. UP/DOWN button on the remote control until the red color level is adjusted to 110% of the white level. (Refer to Fig. 2-7) 9. Receive the color bar pattern of NTSC. (Audio Video Input) 10. Press the TV/AV button on the remote control to set to the AV mode. Then perform the above adjustments 2~8.
[ TV ]
OSD H
A 2-12: SUB BRIGHTNESS
B
Fig. 2-4
1. Place the set with Aging Test for more than 15 minutes. 2. Receive the monoscope pattern. (RF Input) 3. Using the remote control, set the brightness and contrast to normal position. 4. Activate the adjustment mode display of Fig. 1-1 and press the channel button (4) on the remote control to select "PICTURE". The Fig. 2-5 appears on the display. 5. Press the channel button (1) on the remote control to select "BRIGHT". 6. Press the VOL. UP/DOWN button on the remote control until the white 10% is starting to be visible. 7. Receive the monoscope pattern. (Audio Video Input) 8. Press the TV/AV button on the remote control to set to the AV mode. Then perform the above adjustments 3~6. 1. BRIGHT 2. CONTRAST 3. COLOR 4. TINT 5. SHARPNESS 6. OSD CONT 7. 8.
Fig. 2-6
100%
110%
White 100%
RED Level Fig. 2-7
0. RETURN
Fig. 2-5
No.51842
9
|
|
|
> |
|
