|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Good pdf of the service manual for this unit. Includes disassembly instructions, full schematics, board layouts, parts lists and diagnostic information. Some information is in the pdf twice (single pages, and split pages), but that could be how it was originally generated by panasonic, or perhaps the idea is to make it eaiser to put onto 8.5 x 11" pages.
Information was exactly what I needed. Delivery was overnight (less than 12 hours) and I was happy with the process.
;
5 STARS for FAST DELIVERY, BEST PRICES and QUALITY PRODUCT. Item was exactly as described with superb resolution. Will definitely source all my future requirements from this website. Thanks a lot owner-manual.com!
;
OEM manual provided all schematics, board layouts and component specs necessary to facilitate unit maintenance. All pages were clear and readable.
;
Good condition and quality. Hard to find anywhere in Internet, only on this site.
 ;
Exactly what I needed to be able to bring the amp back to life... will come back to this site the next time I need schematics.
CX-LEM220 SECTION 5 MECHANICAL ADJUSTMENTS
TAPE MECHANISM DECK SECTION
Precaution 1. Clean the following parts with a denatured alcohol-moistened swab: record/playback heads pinch rollers erase head rubber belts capstan idlers 2. Demagnetize the record/playback head with a head demagnetizer. 3. Do not use a magnetized screwdriver for the adjustments. 4. After the adjustments, apply suitable locking compound to the parts adjusted. 5. The adjustments should be performed with the rated power supply voltage unless otherwise noted. Torque Measurement
Mode FWD Torque meter CQ-102C Meter reading 2.94 mN � m to 7.84 mN � m 31 to 71 g � cm (0.43 � 0.98 oz � inch) 0.14 mN � m to 0.59 mN � m 2 to 6 g � cm (0.02 � 0.08 oz � inch) 6.86 mN � m to 17.64 mN � m 71 to 143 g � cm (0.98 � 1.99 oz � inch) more than 0.98 N � m 100 g or more (3.53 oz or more)
SECTION 6 ELECTRICAL ADJUSTMENTS
DECK SECTION 0 dB = 0.775 V
Precaution 1. Demagnetize the record/playback head with a head demagnetizer. 2. Do not use a magnetized screwdriver for the adjustments. 3. After the adjustments, apply suitable locking compound to the parts adjust. 4. The adjustments should be performed with the rated power supply voltage unless otherwise noted. 5. The adjustments should be performed in the order given in this service manual. (As a general rule, playback circuit adjustment should be completed before performing recording circuit adjustment.) 6. The adjustments should be performed for both L-CH and RCH. 7. Switches and controls should be set as follows unless otherwise specified. Test Tape
Tape P-4-A100 WS-48B Signal 10 kHz, �10 dB 3 kHz, 0 dB Used for Azimuth Adjustment Tape Speed Check
FWD back tension
CQ-102C
FF/REW
CQ-201B
FWD tension
CQ-403A
Record/Playback Head Azimuth Adjustment Procedure: 1. Mode: Playback
test tape P-4-A100 (10 kHz, � 10 dB) MAIN board SPEAKER terminal (J302) L-CH, R-CH
level meter
set + �
2. Turn the adjustment screw and check output peaks. If the peaks do not match for L-CH and R-CH, turn the adjustment screw so that outputs match within 1dB of peak.
L-CH peak Output level
within 1dB within 1dB
Screw position
R-CH peak L-CH peak R-CH peak
Screw position
12
|
|
|
> |
|
