|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Exactly what was needed to assess the product - excellent value and great service
 ;
Nice to have the service manual for the Sony DCR-TRV345E now. The document is of excellent quality.
;
MACKIE HR824 26 pages English-only Service Manual contains:
1) HR824 technical overview with the description of front and rear panel switches.
2) HR824 specs
3) Block Diagram
4) Wiring Diagram
5) Packaging management
6) Spare part & final assembly list (for PCB rev A and B) + exploded view
7) Test Procedures (where, how to measure voltage...) including Test Point diagram on the PCB.
8) IC and Transistor charts.
Excellent guide: very clear, good scan quality enabling us to print readable diagram :-)
Note:
Mackie HR824 make extensive use of surface mount devices (SMD). Service on the HR824 must
only be undertaken by experienced service technicians with the right tools, experience and patience to perform surface mount rework when needed.
;
This Service manual is very well scanned and its clean to read, no any anti-theft words that un-english could understand. I got my CCD600 working with this manual and it´s clear shematics :)
;
I was very pleased with the service provided and was surprised at how good the quality was of the manual. I thought it may be a third generation copy or so, but it is as good as the websites that charge 3 times this much. I repair some electronics for family and friends without charge, so this is perfect for me. Thank you very much.
BLOCK DIAGRAM
BL101 880-1917E AM/FM TUNER IC301 NJM4558 NAVI AMP Q301 NAVI ON
NAVI(+) NAVI(-) NAVI ON SIGNAL
LPF
IC302 LC75412WH ELECTRONIC VOLUME
IC503 -505 NJM2060 EQ.
MUTE
IC506 TA8275 POWER AMP
FL SP(+) FL SP(-) FR SP(+) FR SP(-) RL SP(+) RL SP(-) RR SP(+) RR SP(-)
CD(GS-1) MECHANISM RF AMP DSP/SSP/DAC
DRIVER
IC201 uPD178076 SYSTEM CONTROL
CD L-IN(+) CD L-IN(-) CD R-IN(+) CD R-IN(-) CD REQ CD RX CD TX
LCD DRIVER IC1101 LC75883
POWER SUPPLY
A/C INTERFACE
KEY MATRIX
CONNECTOR
LCD
J1002
J701 J1001
ANT SIG BACK UP ILL. CONT LIGHTING ACC GND GND GND DATA GND GND NAVI GND
EXPLANATION OF IC
pin 25: ILL AD
052-1173-20
uPD178076GF-568-3BA
System Controller
pin 26: NU pin 27: A VDD
1.Terminal Description pin 1: EJECT SW pin pin pin pin pin pin pin 2: NAVI ON 3: NU 4: VOL DATA 5: VOL CLK 6: VOL CE 7: NU 8: LCD DI
: IN : Eject switch signal input. : IN : NAVI ON signal input. : - : Not in use. : O : The serial data output to the volume IC. : O : The clock pulse output to the volume IC. : O : The chip enable signal output to the volume IC. : - : Not in use. : IN : The srial data input from the LCD driver. : O : The srial data output to the LCD driver. : O : The clock pulse output to the LCD driver. : O : The chip enable signal output to the LCD driver. : O : Reset pulse output to LCD driver. : IN : Power switch ON signal input. : IN : Volume control pulse input from the rotary encoder. : IN : Volume control pulse input from the rotary encoder. : - : Not in use. : IN : Illumination ON signal input. : - : Not in use. : - : Not in use. : - : Not in use. : - : Not in use. : - : Not in use. : IN : Remote control signal input. : IN : Remote control signal input. pin 46: GND PLL pin 47: VT pin 48: NU pin 49: IC pin 28: NU pin 29: NU pin 30: NU pin 31: NU pin 32: A VSS pin 33: REG CPU pin 34: VDD pin 35: REG OSC pin 36: X 2 pin 37: X 1 pin 38: GND pin 39: NU pin 40: GND pin 41: AM IF IN pin 42: FM IF IN pin 43: VDD PLL pin 44: FM OSC IN pin 45: AM OSC IN
: IN : The analog voltage input for illumination signal. : - : Not in use. : - : Positive supply voltage for the Analog section. : - : Not in use. : - : Not in use. : - : Not in use. : - : Not in use. : - : Analog ground. : IN : The capacitor connection terminal to suppress the ripple. : - : Positive supply voltage. : IN : The capacitor connection terminal to suppress the ripple. : - : Crystal connection. : - : Crystal connection. : - : Ground. : - : Not in use. : - : Ground. : IN : The input terminal of the internal counter for AM IF. : IN : The input terminal of the internal counter for FM IF. : - : Positive supply voltage for the PLL. : IN : The input terminal of the internal counter for FM OSC ( Local Oscillation ). : IN : The input terminal of the internal counter for AM OSC ( Local Oscillation ). : - : Ground for the PLL. : O : PLL error signal output. : - : Not in use. : IN : Connect to the ground.
pin 9: LCD DO pin 10: LCD CLK pin 11: LCD CE pin 12: LCD RST pin 13: POWER SW pin 14: VOL 1 pin 15: VOL 2 pin 16: NU pin 17: ILL pin 18: NU pin 19: NU pin 20: NU pin 21: NU pin 22: NU pin 23: REM A pin 24: REM B
-3-
PP-2515L
|
|
|
> |
|
