FUNAI D8D-4110DB
Owner's Manual

E8G04ED(EN).fm Page 8 Friday, December 22, 2006 5:33 PM

External Input Mode (for VCR Features) Connect an external device (a decoder, a camcorder, etc.) to the AV2 (DECODER) jack. Press 0, 0, 2 with the Number buttons, so that �AV2� appears on the TV screen. If you use the front AUDIO/VIDEO input jacks, press 0, 0, 3 with the Number buttons, so that �AV3� appears on the TV screen. If you use the AV1 (TV) jack for connecting a device, press 0, 0, 1 with the Number buttons, so that �AV1� appears on the TV screen. Video Cassette Tape This unit will operate with any cassette that bears the VHS mark. For best results, we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes. � You can prevent accidental erasing of a recording by breaking off the erase-prevention tab on the back edge of the cassette.

5) Press SETUP.
MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK LANGUAGE

LANGUAGE [ENGLISH DEUTSCH TSCHECHISCH POLSKI MAGYAR ]

Setting the Clock This unit incorporates a 24-hour clock. The clock must be set for the Timer Recording function to operate correctly. � Use the remote control for this procedure. 1) Press VCR, then SETUP. 2) Press K or L to select �INITIAL�, then press B. 3) Press K or L to select �CLOCK�, then press B. 4) Press K or L until the relevant year appears, then press B. 5) Press K or L until the relevant month appears, then press
B.

Tab

� If you decide to record on the tape again, cover the hole with plastic tape. TV Colour System Different countries use different television colour systems. Tapes recorded in the PAL, MESECAM or NTSC system can be played back on this unit. Usually, the picture on the TV screen will be in black and white when you play back a tape that is recorded in a different colour system. Tapes recorded in the NTSC system can be played back on this unit and a PAL system TV set. This feature is only available in the SP mode. When playing back such tapes, the picture may roll up or down, shrink vertically and black bars may appear both at the top and bottom of the screen. Adjust the vertical hold control on your TV, if the TV features this control. Turning on Your DVD/VCR The following steps should only be performed if there is a power failure or if this unit is unplugged for more than 30 seconds. � Use the remote control for this procedure. 1) Turn on the TV and select the video channel on the TV. 2) Press STANDBY-ON, then VCR. 3) Press K or L repeatedly to select your desired language. 4) Press SETUP.
LANGUAGE [ENGLISH DEUTSCH TSCHECHISCH POLSKI MAGYAR ]

6) 7) 8) 9)

Press K or L until the relevant day appears, then press B. Press K or L until the relevant hour appears, then press B. Press K or L until the relevant minute appears. Press SETUP to start the clock. Note: � Press s to go back to the item you want to correct during steps 5) to 8). � Although seconds are not displayed, they begin counting from 00 when you exit by pressing SETUP. Use this feature to synchronize the clock with the correct time. � If this unit is unplugged or if there is a power failure for more than 30 seconds, you may have to reset the clock.
MENU TIMER SET UP INITIAL INITIAL CH TUNING CLOCK LANGUAGE

CLOCK YEAR MONTH DAY HOUR MINUTE 2007 01 0_ _ 1 MO __

Changing the Language If you want to change the language used on the TV screen menus, follow the steps below. � Use the remote control for this procedure. 1) Press VCR, then SETUP. 2) Press K or L to select �INITIAL�, then press B. 3) Press K or L to select �LANGUAGE�, then press B. 4) Press K or L repeatedly to select your desired language.

Channel Presetting Tuning of broadcast channels not already preset in the unit can be performed in two ways.
Automatic Channel Preset

� By �AUTOMATICALLY� tuning channels and placing them in sequential order in the unit�s memory i.e. the first channel found will be memorised into the unit�s channel position 1, the second channel found will be memorised into the unit�s channel position 2 and so on.

8

EN