|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
- Very good scan quality, PERFECT!
- Sehr gute scan Qualitaet, empfehlenswert!
Wolfgang Sundhaus
 ;
Good site, works ok and you get what you order, no problems experienced, got my manual within a day. A++++
;
Original well scanned manual. Got the job done. Microwave problem found & corrected. For $5 and a new magnitron from ebay, it was a cheap and good the first shot fix. Electrical schematics allowed me to mage sure every thing else was ok before cutting and order for parts. Hard to live without.
;
I was very skeptical of this website, I have never downloaded manuals before. I put it on the AMEX and payed through Paypal to ensure protection. I got the manual exactly as described and now I can replace the filter capacitor for this amp. Great Price, others selling for 12.99 or more and this is the same manual. I will search out this website for other manuals. Thank you
;
Manual was reasonably easy to follow. I am not an engineer or know much about electronics but with the manuals help I was able to figure out the problem, identify the part required for the repair. Replacement part cost around $30. Whilst replacing the part I was telling myself, "this aint gonna work cos it seems far too easy". Took about 15 minutes to do and my plasma TV works a treat. Would never have been able to do this without the service manual.
HCD-S500/S800
[0] Reset SLED TILT [1] LD [2] SP [3] Focus [4] TRK [5] Sled [6] CLVA
Reset the Sled and Tilt to initial position. Turn ON/OFF the laser. Turn ON/OFF the spindle. Search the focus and turn on the focus. Turn ON/OFF the tracking servo. Turn ON/OFF the sled servo. Turn ON/OFF normal servo of spindle servo. Apply same voltage as that of focus search to the focus drive to check the focus drive system. Move the sled outward. Perform this operation with the tracking servo turned off. Move the sled inward. Perform this operation with the tracking servo turned off. Move the tilt upward. Move the tilt downward.
6. Memory Check
EEPROM Data1 CD xx xx xx -� DL �LCD SL L0 xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx L1 xx xx xx xx xx xx xx xx
Focus Gain TRK. Gain FCS Balance
Focus Bias xx xx TRV. Offset xx xx L. F. Offset xx xx EQ Boost xx xx Mirror Time xx xx _DOWN: Next Data CLEAR: Default Set EEPROM Data1 CD RF Jitter xx RF Level xx FE Level xx FE Balance xx TRV. Level xx Analog FRSW xx PLL DacGain xx _ UP : Prev Data CLEAR: Default Set
page.1/2
[7] FCS. Srch
� Sled FWD
� Sled REV
-� DL �LCD SL L0 -xx xx -xx --xx --xx --xx -xx xx xx xx xx xx
L1 xx ----xx xx
page.2/2
� Tilt UP � Tilt DOWN
The following menus are normally not used. 3. Track/Layer Jump 4. Manual Adjustment 5. Auto Adjustment
This screen displays current servo adjusted data stored in the EEPROM. Though adjusted data can be initialized with the [CLEAR] key, they cannot be restored after initialization. So, before clearing, make a note of the adjusted data. For reference, the drive has been designed so that the gain center value is 20 and offset value is 80. Other values will be in a range of 10 to 80. If extreme value such as 00 or FF is set, adjustment will be faulty. In such a case, check for disc scratch or cable disconnection, then perform adjustment again. 7. Sacd Water Mark
The persons who do not know well about these menus should not use them.
4-12. MECHA AGING
### Mecha Aging ###
Press OPEN Key
Abort: STOP key
On the Test Mode Menu Screen, selecting [3] executes the aging of the mechanism. Start aging with PLAY. During aging, the repeat cycle is displayed. Aging can be aborted at any time by pressing the x key. After the operation is stopped, press the x key or [RETURN] key again to return to the Test Mode Menu. SEARCH Aging is only for a CD.
20
|
|
|
> |
|
