|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It`s not your fault tear down is rather incomplete. It doesn`t have complete instructions as to deconstruction for repair.
 ;
THANK YOU FOR A GOOD TRANSACTION, NICE COPY, CLEAR
;
Very Good! All the diagram are easy to read, and its complete.
;
This was an excellent source of detailed assembly information on a device which is at least 12 years old. A very lucky find, coupled with great service.
;
Excellent Service Manual and best price on the Internet. This Service Manual covers everything you could ever need including full circuit schematics, component layout diagrams, stripdown procedure and full parts list/breakdown. I needed this to carry out a modification to one of these headunits and this manual covered everything I needed. Fast delivery, processed within a few hours.
3-864-485-01 (1)
A
5
English
Features
Battery Adaptor
1 1
� DC-L10 is a battery adaptor for the 6-inch/9-inch color video monitor that uses the BP-L60/BP-L90 lithium battery pack. 6-inch: PVM 41 Series 9-inch: PVM/BVM 41/44 Series � The upper adaptor is easy to detach. Simply loosen the bracket screws. This is handy for removing the battery when it is being transported. � If the 6-inch/9-inch monitor is combined with a tuner (TU1041U/TU-1040E), you can install the battery adaptor on the monitor by adding a power cord. Contact your Sony dealer or local authorized Sony service facility for the additional power cord.
Operating Instructions Mode d�emploi Bedienungsanleitung Manual de instrucciones Istruzioni per l�uso
2
3
4
B
1
1) 2)
C
Parts identification A
1 Bracket screws 2 Handle 3 Battery detach button 4 Fuse holder (5A) 5 DC power cord (4-pin XLR)
OPERATING INSTRUCTIONS
Installing the battery adaptor on the monitor B
1 2
1) Remove the monitor screws. 2) Install the brackets on both sides of the monitor. Lock with the supplied screws (� 4). Place the battery adaptor on the brackets. Lock the battery adaptor with the bracket screws (� 4). You can tighten the screws with fingers, a coin or screwdriver. 1) Place the cable clamp on the screw at the upper right rear of the monitor. 2) Connect the power plug to the monitor�s DC 12V input connector. Secure the DC power cord with the cable clamp.
DC-L10
Sony Corporation © 1998
Printed in Japan
3 2
Folding the handle C
D
Push down on both sides of the handle and fold in either direction. Make sure you fold the handle all the way down. If the handle is not properly folded, the battery adaptor may not function properly.
Installing the battery pack D
As shown in the figure, while the handle is folded down, place the battery pack on the battery adaptor. Slide the battery pack in the direction of the arrow. Push the battery pack in until it is locked. To remove the battery pack, push the battery detach button.
Battery detach button
Accessories supplied E
1 6-inch brackets (2) 2 9-inch brackets (2) 3 Screws M4 � 14 (8, including 4 extra) 4 Cable clamp (for DC power cord) (1) 5 Instruction manual (1)
3
1)
Cableclamp
E
5 4 3 2
Specifications
Dimensions 315 � 146 � 100mm (12 1/2 � 5 3/4 � 4 inches) (w/h/d) (The bracket is not included; the handle is upright.) Mass Battery adaptor: Approx. 1.4kg (3 lb 14 oz) 6-inch bracket (2): Approx. 800g (1 lb 12 oz) 9-inch bracket (2): Approx. 1,000g (2 lb 3 oz) Design and specifications are subject to change without notice.
This section is extracted SECTION 1 from operation manual.
1
2)
Power plug
1-1 (E) DC-L10
|
|
|
> |
|
