|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
This is a good quality scan of the original Service Manual from Nordmende, Germany. Contains the circuit diagram, PCB layout, adjust/tune instructions as well. It is NOT in English but in GERMAN language! That was quite right for my german friend from the lower east side in Berlin.
 ;
Received via e-mail this PDF manual is worth the money. This is a quality scan of a manual in excellent condition and is just as good as having the original manual in hand. I have later seen the original manual and it was printed in colour, but this particular manual is black & white but scan resolution is high end quality! All drawings and pictures are presented in great detail. So, nearly perfect score in my opinion.
If you own the turntable you also should own the manual!
;
I was very satisfied with the service manual I ordered and downloaded. I will definitely buy again from this seller.
;
Great product. Recieved it fast...exactly as advertised.
;
Manuals were delivered promptly and were correct as advertised. No issues with the download link which was provided promptly after everything was processed. Very pleasant experience
ENGLISH
1-5-3. Self-diagnosis Code Table
Self-diagnosis Code Block Function C C C C C 0 1 1 2 3 4 3 3 1 2 Detailed Code 0 0 0 0 5 0 0 2 0 0 Symptom/State Correction
Repaired by:
JAPANESE
Non-standard battery is used. Faulty disc is used. Disc access error Condensation. Codec IC dose not return any reply Difficult to adjust focus (Cannot initialize focus) EEPROM data are rewritten. Drive fault Codec IC fault Audio Codec IC fault Zoom operations fault (Cannot initialize zoom lens.) The abnormalities in initialization of the focus lens and the abnormalities in initialization of the zoom lens occurred simultaneously. Handshake correction function does not work well. (With PITCH angular velocity sensor output stopped.) Handshake correction function does not work well. (With YAW angular velocity sensor output stopped.) Abnormality when flash is being charged. Fault of writing to or erasing the flashmemory Fault of writing to or erasing EEPROM
C E E E E
3 2 3 4 4
2 0 1 0 0
6 0 0 0 0
0 0 0 0 1
E
6
1
1
0
Use the InfoLITHIUM battery. Use a compatible disc with the camcorder. Clean the disc with the supplied cleaning cloth. Use a compatible disc with the camcorder. Remove the disc, and insert it again after one hour. Remove the power source. Reconnect it again and operate your camcorder again Retry turn the power on by the power switch. If it does not recover, check the focus MR sensor of lens block (pin ql, wa of CN2101 on the VC-439 board). If it is OK, check the focus motor drive IC (IC2104 on the VC-439 board). Make EEPROM data correct value. (Note 1) Inspect or replacement of the mechanism deck, IC (IC4301 on the MD-129 board) and drive block Inspect or replacement of the codec IC (IC3001on the VC-439 board) peripheral circuits Inspect or replacement of the Audio Codec IC (IC3001 on the VC-439 board) peripheral circuits Inspect the lens block zoom MR sensor (pin qh, qk of CN2101 on the VC-439 board) when zooming is performed when the zoom lever is operated, and the zoom motor drive circuit (IC2104 on the VC-439 board) when zooming is not performed. Check both C: 32: 60 and E: 61: 10 of the self-diagnosis code.
E
6
1
1
1
E
6
2
0
0
Inspect PITCH angular velocity sensors (SE6801 on the CM-069 board) peripheral circuits. Inspect YAW angular velocity sensors (SE6802 on the CM-069 board) peripheral circuits. Checking of flash unit or replacement of flash unit. (Note 2) Inspect the flash memory (IC3101 on the VC-439 board). (Note 1) Inspect the EEPROM (IC2602 on the VC-439 board). (Note 1)
E E E E
6 9 9 9
2 1 4 4
0 0 0 0
1 1 0 1 -
Note1: Refer to �10-2. Record of Self-diagnosis check� of �3-5. SERVICE MODE�, ADJ (9-876-938-51). Note2: After repair, be sure to perform �1-6. PROCESS AFTER FIXING FLASH ERROR�.
DCR-DVD505/DVD505E/DVD905/DVD905E_L2 1-3
|
|
|
> |
|
