|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
It took about 24-hours after my payment before I was able to get to the download. Apparently, payment processing is not 100% automated. That is no big deal, just be aware of that going in.
After I got to it, it was in good shape, easy to read, etc. Not some cheap FAX copy looking thing.
Also, this site was the cheapest I found. Another Plus!
 ;
Good price, very legible manual, exactly what I needed -- but had to wait a day to actually get the download of the manual. Would have preferred to download it immediately after payment rather than waiting for someone to "process" my order. I was surprised that I had to wait that long.
;
As the only source for this manual it rather rank quite high since it is well scanned and perfectly readable.
;
the manual is in good quality and it's in pdf. manual was send in less then 24h.
regards
mike
;
I would not plug this machine in without finding a manual like this. In addition to setup and normal operating instructions, it has troubleshooting flowcharts, diagrammed mechanical adjustments, and schematics to beat the band. The tech I hand it to would be thrilled to find solder side PCB diagrams with component outlines superimposed, pinouts for every IC chip, and line drawings of transistors, with labeled legs.
As for printing quality, this may be a copy of a copy, but even the finest print when enlarged is very legible. There is a bit of grayed print over a few pages, as if a wet page were placed over it, but the print is still very legible. If you could borrow an original manual and get it printed and bound for 4 to 6 times the cost, you could get better quality. In that case you wouldn't be here. For price, utility, and availability I am rating this manual highly.
1. Playback Level Check Mode VTR playback Signal Measurement Point Measuring Instrument Specified Value Alignment tape: For audio operation check(XH5-3P) Audio left or right terminal of AUDIO VIDEO jack Audio level meter and frequency counter 32 kHz mode: 1 kHz, +3.0 ± 2.0dBs 48 kHz mode: 1 kHz, +3.0 ± 2.0dBs 44.1 kHz mode: The 7.35kHz signal level during EMP OFF is +2.0 ± 2.0dBs. The 7.35kHz signal level during EMP ON is �6 ± 2 dB from the signal level during EMP OFF.
4. Overall Noise Level Check Mode Camera recording and playback Signal Measurement Point Measuring Instrument Specified Value No signal: Insert a shorting plug in the MIC jack Audio left or right terminal of AUDIO VIDEO jack Audio level meter Below �45dBs (IHF-A filter ON, 20kHz LPF ON)
Checking Method: 1) Insert a shorting plug in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the noise level is the specified value. 5. Overall Separation Check Mode Camera recording and playback Signal 400Hz, �66dBs signal: MIC jack <right> [left] (Connect the MIC jack <left> [right] to GND) Audio <left> [right] terminal of AUDIO VIDEO jack Audio level meter Below �40dBs (IHF-A filter ON)
Checking Method: 1) Check that the playback signal level is the specified value. 2. Overall Level Characteristics Check Mode Signal Measurement Point Measuring Instrument Specified Value Camera recording and playback 400Hz, �66 dBs signal: MIC jack left and right Audio left or right terminal of AUDIO VIDEO jack Audio level meter �7.5 ± 3.0dBs
Measurement Point Measuring Instrument Specified Value < > : Left channel check [ ] : Right channel check
Checking Method: 1) Input the 400Hz, �66dBs signal in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the 400Hz signal level is the specified value. 3. Overall Distortion Check Mode Camera recording and playback Signal Measurement Point Measuring Instrument Specified Value 400Hz, �66dBs signal: MIC jack left and right Audio left or right terminal of AUDIO VIDEO jack Audio distortion meter Below 0.4% (200Hz to 6kHz BPF ON)
Checking Method: 1) Input the 400Hz, �66dBs signal in the <right> [left] terminal of the MIC jack only. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the signal level of the audio <left> [right] terminal is the specified value.
Checking Method: 1) Input the 400Hz, �66dBs signal in the MIC jack. 2) Record in the camera mode. 3) Playback the recorded section. 4) Check that the distortion is the specified value.
5-50
|
|
|
> |
|
