|
|
|
Categories
|
|
Information
|
|
Featured Product
|
|
|
 |
|
|
There are currently no product reviews.
 ;
Excellent service manual, the only known point of note is the alignment of improvability scanned pages within the pdf page. The resolution is good.
;
I was very glad recieving the service manal from You. Additionaly very fast. Extremaly nice servicing. Thanks very mach! Now my GX-220 working better, than it was made. Alexander from Moscow, Russia/
;
Sweet! I won the item on eBay and couldn't adjust the geometry or even keep a steady picure. This guide has the full schematics (not available anywhere else as far as I could tell), and was a bargain for the wealth of knowledge it contains. I hooked it up to my testing equipment, tweaked a few potentiometers and got it playing videogames in no time. Thanks!
;
It was just what I need to fix my old BMW's CD player. Very convenient also. Thank you.
;
Great Manual! It contains all the wiring schematics and mechanical exploded views that are essential for service and repair. I was surprised I even found this for such an old machine. Only wish I knew of this site many years ago.
4-15. LS Guide Roller, Guide Lock Plate (T), Pinch Pusher Assembly, Eject Arm
1. Removal procedure
1) 2) 3) 4) 5) 6) 7) 8) 9) Remove the LS chassis block assembly. (Refer to 4-10.) Remove the LS guide roller 1. Remove the P pressure plate spring 2. Remove the HLW cut (0.98 � 3 � 0.25) 3. Remove the pitch pressure plate assembly 4 in the direction of the arrow A. Remove the relay gear 5. Remove the screw (camera pan2 M1.4 � 1.6) 6. Remove the guide lock plate (T) 7 in the direction of the arrow B. Remove the eject arm spring 8 and HLW cut (0.98 � 3 � 0.25) 9.
Note: Do not reuse the HLW cut.
2. Attachment procedure
1) 2) Attach the eject arm spring 8 to the eject arm 0. Hook one end of the eject arm spring 8 on the protrusion of the main chassis block assembly and attach the eject arm to the shaft. Attach the HLW cut (0.98 � 3 � 0.25) 9. Do not reuse the HLW cut. Attach the guide lock plate T 7 while aligning it with the notches C and D. Attach the screw (camera pan2 M1.4 � 1.6) 6. Tightening torque: 0.078 ± 0.01 N�m (0.8 ± 0.1 kgf�cm) Attach the relay gear 5. Attach the pinch pusher plate 4 with the HLW cut (0.98 � 3 � 0.25) 3. Attach the P pressure plate spring 2. Insert the concave side of the LS guide roller 1 into the shaft to attach the LS guide roller.
Note: Insert the roller completely.
3) 4) 5) 6) 7) 8)
10) Remove the eject arm 0.
9)
Attach the LS chassis block assembly to the mechanical chassis. (Refer to 4-10.)
Notch D Notch C
6 Screw (camera pan 2 main M1.4 � 1.6) 7 Remove the guide lock plate (T) in the direction of the arrow B. B
Coat inside with grease too.
3 HLW cut (0.98 � 3 � 0.25) 4 Remove the pinch pressure plate assembly in the direction of the arrow A.
Pinch the rotary switch.
9 HLW cut (Do not reuse) (0.98 � 3 � 0.25) 0 Eject arm A 5 Relay gear
8 Eject arm spring
Concave side Coat inside with grease too.
2 P pressure plate spring 1 LS guide roller
When attaching it, coat the hatched portion with grease.
Fig. 4-15.
� 28 �
|
|
|
> |
|
